OTT-LITE TECHNOLOGY 2559246K Manual De Instrucciones

25W Davenport Floor Lamp
2559246K
INS50002Rev.0509
H
G
F
E
M
J J
L
I
K
D
B
A
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE
OTHER) AS A FEATURE TO REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL
FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN
THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY
INSERTED. DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualified person in order
to avoid a hazard.
Indoor use only.
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE
(UNE LAME PLUS LARGE QUE L'AUTRE). CE DISPOSITIF DE SÉCURITÉ DIMINUE LE
RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE DANS LA PRISE
QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS
AVEC UNE RALLONGE SAUF SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS
CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE
BOUT LARGE DE LA FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
Si le câble d'alimentation est endommagé, il doit être remplacé par le
fabricant, son agent de service ou une personne qualifiée afin d'éviter
les accidents.
Utilisation intérieure seulement.
¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO
(UNA DE SUS PATAS ES MÁS ANCHA QUE LA OTRA) COMO CARACTERISTICA PARA
REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE ENCAJARÁ EN
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE
NO CALZA COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO
ENCAJA, PÓNGASE EN CONTACTO CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE
UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA SER TOTALMENTE INSERTADO.
NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR
LA PATA ANCHA DEL ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
Si el cordón sufre algún daño, debe ser reemplazado por el fabricante,
su agente de servicio o persona similarmente calificada para evitar
cualquier peligro.
Sólo para uso en interiores.
ENGLISH
25W Davenport Floor Lamp
LAMP ASSEMBLY
1. Unpack all lamp parts and lay out on the floor with the base (A)
lying flat.
2. Thread Middle Section (C) to Upper Section (D) by hand, turning
clockwise until tight.
3. Thread Lower Section (B) to Middle Section (C) by hand, turning
clockwise until tight.
4. Thread Lower Section (B) to Base (A) by hand, turning clockwise
until tight.
5. Attach Harp (E) to Harp Holder (I) by squeezing open ends
of harp, placing flattened section inside of Harp Holder (I) and
releasing. End by sliding Harp Brackets (J) over Harp Holder (I).
6. Assemble knock-down Shade (F) by:
6A. Holding shade upside down, so it will open.
6B. Pushing interior wire supports downward and outward until they
snap in place inside the top rim of the shade.
7. Place Shade (F) on Harp (E).
8. Place Reflector (G) on top of Shade (F), making sure the white
side faces down.
9. Thread Finial (H) onto shade and Reflector by hand, turning
clockwise until snug.
10. Install bulb following BULB INSERTION/ REPLACEMENT
instructions.
1 1. Plug the lamp into a standard 120V outlet.
12. Turn lamp on or off by rotating Socket Switch (K) clockwise.
BULB INSERTION/REPLACEMENT
1. Make sure the lamp is not plugged into an electrical socket.
2. If the lamp has been in use, allow it to cool for approximately five
minutes before proceeding.
3. To remove a bulb (M) already installed in the lamp, grasp it firmly
in your hand and pull it straight out of the socket (L). Do not twist
or turn the bulb while removing it from the socket.
4. To install a bulb (M) in the socket (L), grasp the bulb firmly in
your hand and push the bulb straight into the socket by applying
pressure to the base of bulb, until it "snaps" into place. Do not apply
pressure to the glass end of the bulb.
5. Plug the lamp into a standard 120V socket, and your lamp is ready
for use.
®
Please note that in operation, OTT-LITE bulbs are not dimmable.
Enjoy your OTT-LITE ® Davenport Floor Lamp!
This lighting system is designed for use with OTT-LITE VisionSaver
Plus ® bulbs only (model number H3400K). Use of other products
voids the warranty and may result in damage to the lighting system.