Publicidad
Idiomas disponibles
Idiomas disponibles
4-WAY INSTALLATION (3+ Dimmers) Continued
Accessory
Accessory
Switch
Dimmer
Black
Hot
Green
Ground
Neutral
FACTORY RESET
ONLY DO THIS STEP IF YOU ARE UNABLE TO REMOVE THE
DEVICE USING THE APP .
If removal does not work, delete it in the app by clicking "my
device is broken" and then follow the factory reset steps:
1.
Press and hold the ON button for 12 seconds to reset.
2.
The load may turn OFF or ON and the LED will start flashing
indicating the reset is processing. The LED will continue
flashing to indicate that the dimmer is ready to be paired
with the HALO Home App.
FCC Statement
This device complies with Part 15 of the FCC
•
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
•
interference.
(2) This device must accept any interference
•
received, including interference that may
cause undesired operation.
N
ote:
The grantee is not responsible for any
changes or modifications not expressly
approved by the party responsible for
compliance. Such modifications could void the
user's authority to operate the equipment.
N
ote:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates uses and can
•
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the
•
equipment and receiver.
5-YEAR WARRANTY
For warranty information, please visit
www.cooperlighting.com/legal
4-WAY WIRING DIAGRAM
Black
Red
Traveler Wires
Green
White
Ground
FCC STATEMENT
Connect the equipment into an outlet on a
•
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
•
technician for help
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: 2AKCY-HIWMA1BLE40A
Responsible Party – U.S. Contact Information
Cooper Lighting Solutions
1121 Highway 74 S
Peachtree City, GA 30269
www. cooperlighting.com
IC Statement
This device contains licence-exempt
•
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation
is subject to the following two conditions: 1.
This device may not cause interference. 2. This
device must accept any interference, including
interference that may cause undesired operation
of the device.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Accessory
Accessory
Switch
Dimmer
Red
Traveler Wires
White
CIRCUIT DISCONNECT (AIR-GAP)
To replace a bulb, disconnect power to this dimmer and any
connected loads by using a flathead screwdriver to pull the air-
gap dimmer out until you hear a click. For anything other than
bulb replacement, power must be disconnected at the circuit
breaker.
© 2021 Cooper Lighting Solutions
All Rights Reserved.
Specifications and dimensions
subject to change without notice.
Smart
Smart
Dimmer
Switch
Red
Black
Green
White
Ground
FCC ID: 2AKCY-HIWMA1BLE40
IC: 4706A-HIWMA1BLE40
SAVE THESE INSTRUCTIONS AND
WARNINGS.
SUPPLEMENTAL INFORMATION
Construction of control: Independently
Mounted for Flush Mounting
Type of Action: Type 1.B Action
Pollution Degree: 2
Rated Impulse Voltage: 2500 V
Software Class: Class A
Load
Neutral
Standard
Light(s)
IL517016EN page 6
February 3, 2021 11:42 AM
Publicidad
