Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The machine is intended for hammer drilling in concrete,
brick and stone as well as for light chiseling work. It is also
suitable for drilling without impact in wood, metal, ceramic
and plastic.
1. INSERTING AND REMOVING DRILL BIT
(SEE FIG. A)
INSERTING
Clean the bit shank and apply grease before installing the
bit. Hold the rotary grip, pull back the locking sleeve and
insert the bits into the bit holder. Turn the bit and push it
in until a resistance is felt, the shaft drops completely into
bit holder. Once you are satisfied it has seated, release the
black locking sleeve. This should lock the bits into position.
After installing always make sure that the tool is securely
held in bit holder by trying to pull it out.
If the bit is not located well, repeat the installation operation
again.
REMOVING
To remove the bit, pull back the locking sleeve, hold and pull
the bit out.
2. ADJUSTING THE AUXILIARY HANDLE
(SEE FIG. B)
For your personal safety we recommend using the auxiliary
handle at all times.
To adjust the handle, rotate the bottom of the handle anti-
clockwise and rotate the handle around the hammer collar
until the handle is in the desired position. Tighten fully.
3. ANTI-VIBRATION HANDLE
The Anti-vibration handle reduces the vibration, making
operation more comfortable and secure.
4. ON/OFF SWITCH (SEE FIG. C)
Depress the On/Off switch to start and release it to stop
your tool.
5. HAMMER DRILL FUNCTION (SEE FIG. D1,
D2)
1. Adjust the hammer or chisel action selector to
position "
". (See Fig.D1)
2. Adjust the hammer or drilling action selector to
position "
". (See Fig. D2)
EN
3. You are now set up for hammer drilling into masonry.
NOTE: Press the selector switch lock button before
adjusting the dial selector every time.
6. DRILLING FUNCTION (SEE FIG. E1, E2)
1. Adjust the hammer or chisel action selector to position
"
". (See Fig. E1)
2. Adjust the hammer or drilling action selector to position
" ". (See Fig. E2)
3. You are now set up for drilling function.
NOTE: Press the selector switch lock button before
adjusting the dial selector every time.
7. CHISEL FUNCTION (SEE FIG. F1, F2)
1. Adjust the hammer or chisel action selector to position
"
" . (See Fig. F1)
2. Adjust the hammer or drilling action selector to position
"
". (See Fig.F2)
3. You are now set up for chisel work using chisel action.
NOTE: Press the selector switch lock button before
adjusting the dial selector every time.
WARNING: You must make sure that the
selector switch is positively locked in
chisel mode position. If not, it could cause a
hazard.
8. DUST COVER (SEE FIG. G)
Before drilling, fit the dust cover over the drill bit.
CAUTION: Always wear eye protection with this
tool.
9. LUBRICATION MACHINE (SEE FIG. H)
The gearbox is lubricated with grease. Refilling is required
when the hammer efficiency is low. Open the cover using
the key and add general purpose lithium based grease.
CAUTION: Keep the container of grease away
from children.
10. SAFETY CLUTCH PROTECTION
This tool will generate high forces when use. Always hold
the tool with both hands and adopt a secure posture.
If the drill bit or chisel becomes jammed in the workpiece,
the clutch will activate stopping the tool spindle. This is
normal.
Switch the machine off, loosen and remove the drill bit or
chisel from the work piece.
CAUTION:
Switching the machine on with the drill bit or chisel
jammed in the work piece will generate high reaction
torque and can result in injury.
13
Publicidad
