Publicidad
Idiomas disponibles
Idiomas disponibles
10 - 14 For driving screws into soft and hard material
15 - 19
For driving screws into hard wood
20 - 21
For driving larger screws
For heavy drilling
6. USING THE LED LIGHT
To turn on the light simply press the on/off switch. When
you release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or enclosed
area.
7. BELT CLIP (SEE FIG. G)
Screw the Belt Clip on the tool with the screw provided in
the plastic bag. The belt clip can be hooked on your belt or
pocket, etc.
8. DRILLING
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location. This will prevent
the drill bit from slipping off center as the hole is started.
Hold the tool firmly and place the tip of the bit at the point
to be drilled. Depress the switch trigger to start the tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
Tungsten carbide drill bits should
always be used for concrete and
masonry. When drilling in metal, only use HSS
drill bits in good condition. Always use a
magnetic bit holder (not included) when using
short screwdriver bits. When screw-driving,
apply a small quantity of liquid soap or similar
to the screw threads to ease insertion.
9. DISPOSAL OF AN EXHAUSTED BATTERY
PACK
To preserve natural resources, please recycle or
dispose of the battery pack properly. This battery
pack contains Lithium batteries. Consult your local
waste authority for information regarding available
recycling and/or disposal options. Discharge your battery
pack by operating your drill, then remove the battery pack
from the drill housing and cover the battery pack
connections with heavy-duty adhesive tape to prevent
short circuit and energy discharge. Do not attempt to open
or remove any of the components.
20
10. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the
load on the machine immediately and allow cooling for
approx. 30 seconds at the highest no-load speed.
11. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature of 75°C is exceeded, the
electronic control switches off the power tool until the
temperature is in the optimum temperature range again.
12. PROTECTION AGAINST DEEP
DISCHARGING
The Li-ion battery is protected against deep discharging
by the "Discharging Protection System". When the battery
is empty, the machine is switched off by means of a
protective circuit: The inserted tool no longer rotates.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON
WHEN YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on top of
the trigger, is positioned in the lock function. Unlock the
forward/reverse rotation control by putting it into the
required rotation position. Push the trigger and the drill
will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting ring, you
can find the torque-adjusting ring between the chuck and
the drill body. Position 1 is the lowest torque (screw
driving force) and position 21 is the highest torque (screw
driving force). Position
the torque adjusting ring to a higher position to reach
the best result.
3. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and having not used a
battery pack for a prolonged time will reduce the battery
pack working time. This can be corrected after several
charge and discharge operations by charging & working
with your drill. Heavy working conditions such as large
screws into hard wood will use up the battery pack energy
faster than lighter working conditions. Do not re-charge
your battery pack below 0
affect performance.
is for drill operation. Regulate
C and above
40
C
as this will
o
o
EN
Publicidad
