Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Insert the holder (4) into the opening (see fig. 7).
4.
Fasten the holder (4) with the knurled screw (3).
5.
Mount the retaining device (23) to the saw blade
guard (5). Insert the screw (24) into the holder (4).
Tighten the screw (24) using a Phillips screwdriver
(not included in the scope of delivery).
6.
Insert the saw blade (21) again as described in 8.2.
7.
Ensure that the retaining device (23) does not
touch the saw blade (21).
8.1.1 Adjusting the retaining device
NOTE:
The retaining device (23) must always be adjusted ac-
cording to the workpiece height. However, the work-
piece should not be clamped, but should rather be able
to move freely. The retaining device (23) is used to lock
the workpiece so that it cannot swing upwards, which
would destroy the saw blade (21).
1.
Loosen the knurled screw (3) to adjust the retain-
ing device (23).
2.
Adjust the retaining device (23) according to the
height of the workpiece.
3.
Re-tighten the knurled screw (3).
8.2 Mounting / changing the saw blade (fig. 1, 7-11)
m WARNING
To avoid injuries due to unintentional start up: Be-
fore removing or replacing the saw blade, always
press "0" and remove the mains plug from the
socket.
8.2.1 Removing/inserting the table inlay
1.
Loosen the knurled screw (3).
2.
Set the saw blade guard (5) all the way up to the
top position.
3.
Reach under the saw table (6) and press the table
inlay (25) upwards.
4.
It is now possible to remove the table inlay (25).
Pay attention to the position of the sawing gap when
inserting the table inlay (25). The table inlay (25) must
be inserted as shown in Fig. 8. Otherwise the machine
can be damaged during mitre cuts.
8.2.2 Removing the saw blade without pins
(optional)
1.
To remove the saw blade (21), remove the table
inlay (25) upwards. (see 8.2.1)
2.
First, release the tension by flipping the tension le-
ver (11) upwards. If necessary, the tension can be
further reduced by turning the tightening lever (11)
counterclockwise.
3.
Press the support (12) down lightly (see fig. 9).
4.
Then loosen the upper saw blade clamping screw
(27).
5.
Now hold the sawblade firmly, otherwise it will fall
into the interior of the machine.
6.
Loosen the lower saw blade clamping screw (28)
with the Allen key (22).
7.
Remove the saw blade upwards.
8.2.3 Inserting the saw blade without pins
(optional)
The teeth of the saw blade must always point down-
wards.
1.
Fix the saw blade (21) in place in the bottom saw
blade holder (29). To fix the saw blade (21) in
place, tighten the lower saw blade clamping screw
(28) with the Allen key (22).
2.
Press the support (12) down lightly. Fasten the oth-
er end of the saw blade (21) in the top saw blade
holder (26) (see fig. 9).
3.
Fasten the saw blade (21) using the upper saw
blade clamping screw (27) (see fig. 10).
4.
Tension the saw blade (21) with the tightening le-
ver (11) by pressing down on it again. Check the
tensioning of the saw blade (21). If the tension is
too low, you can increase it by turning it clockwise.
Before doing this, release the tightening lever (11)
again.
5.
Re-insert the table inlay (25). (see 8.2.1)
8.2.4 Removing the saw blade with pins
1.
To remove the saw blade (21), remove the table
inlay (25) upwards. (see 8.2.1)
2.
First, release the tension by flipping the tension le-
ver (11) upwards. Continue reducing the tension by
turning counterclockwise as required.
3.
Hold the sawblade firmly and press the arm (12)
down slightly (see Fig. 9).
4.
Remove the saw blade from the top and bottom
saw blade holder (26/29).
www.scheppach.com
GB | 31
Publicidad
