Publicidad
Idiomas disponibles
Idiomas disponibles
4. TWO-SPEED GEAR CONTROL (SEE FIG. G)
The drill has a two-speed gear control designed for drilling
or driving at LO (mark is 1) or HI (mark is 2) speeds. A slide
switch is located on top of the drill to select either LO or
HI speed. When using the drill in the LO speed range, the
speed will decrease and the drill will have greater power and
torque. When using the drill in the HI speed range, the speed
will increase and the drill will have less power and torque.
GEAR I
Low speed range: for screwdriving or working with large
drilling diameter.
GEAR II
High speed range: for working with small drilling diameter.
WARNING: To prevent gear damage,
always allow the chuck to come to a
complete stop before changing the direction
of rotation or the two-speed gear control.
WARNING: When overload occurs
frequently on the high speed gear,
switch to the low speed gear to avoid the
motor overheating.
5. CHUCK ADJUSTMENT (SEE FIG. H)
To open the chuck jaws rotate the front section of the chuck.
Insert the drill bit between the chuck jaws and rotate the
front section in the opposite direction. Ensure the drill bit is
in the center of the chuck jaws. Finally, firmly rotate the front
chuck section in the opposite directions. Your drill bit is now
clamped in the chuck.
6. TORQUE ADJUSTMENT (SEE FIG. I)
The torque is adjusted by rotating the torque adjustment
ring. The torque is greater when the torque adjustment ring
is set on a higher setting. The torque is less when the torque
adjustment ring is set on a lower setting.
Make the setting as follows:
1 - 6
for driving small screws
7 - 12
for driving screws into soft material
13 - 18
for driving screws into soft and hard material
for heavy drilling
7. USING THE LED LIGHT
To turn on the light simply press the on/off switch. When
you release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or enclosed
area. LED is also a battery capacity indicator. It will flash
when power gets low.
20
8. BATTERY CAPACITY INDICATOR
Your tool is equipped with battery capacity indicator.
Press the on/off switch halfway or fully, the battery
capacity indicator will light up to show the amount of
charge left in the battery.
Fuel Gauge
3 lights
2 lights
1 light
9. USING BELT CLIP (SEE FIG. J)
Screw the Belt clip on the tool with the screw . The Belt clip
can be hooked on your belt or pocket, etc.
10. DRILLING
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location. This will prevent
the drill bit from slipping off center as the hole is started.
Hold the tool firmly and place the tip of the bit at the point
to be drilled. Depress the switch trigger to start the tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
If you want to activate the drill function (For drilling metal
wood or plastic), turn the torque adjustment ring on the
drill position.
WARNING: When drilling in metal, only
use HSS drill bits in good condition.
Always use a magnetic bit holder (not
included) when using short screwdriver bits.
When screw-driving, apply a small quantity of
liquid soap or similar to the screw threads to
ease insertion.
11. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the
load on the machine immediately and allow cooling for
approx. 30 seconds at the highest no-load speed.
12. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature of 75°C is exceeded, the electronic
control switches off the power tool until the temperature is
in the optimum temperature range again.
Capacity
> 70%
40%~70%
< 40%
EN
Publicidad
