Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Charging Indication:
1. Charging: LCD battery level bar flashes and voltage value
increases;
2. Full charged: LCD battery level bars is full and still, with "FUL"
displayed the voltage is approx. 14.4V.
Note: After charging is completed, and the charger is not
disconnected, the charging mode will be automatically restored
if the battery voltage drops to 12V. It is recommended to
recharge the Jump Starter every 3-4 months to maintain the
efficiency and prolong the service life of the internal battery
even if the unit has not been used.
Output 12V 10A with Cigarette Lighter
WARNING: This port is not a charging interface. It should not be
connected to live equipment at any time, nor should the output
positive and negative terminals be shorted.
1. Plug one end of the equipped cigarette lighter adapter into
the product's 12V 10A output.
2. Connect the 12V electronics/vehicle product to the other end
of the cigarette lighter adapter cable.
3. Short press the "POWER" button (7) to start supplying power
supply with 12V voltage and 10A maximum current for the
vehicle.
Jump Start
WARNING: When using this unit to start, make sure the positive
and negative connections are correct, otherwise the battery
may explode.
Follow the steps below for jump start, otherwise it will be
dangerous:
1. Insert "Smart Clamps" into the engine start port of the device
first.
2. Connect the red (+) clamp with the positive (+) side of the
battery.
3. Connect the black (-) clamp with the metal part of the engine
(negative ground) or to the negative battery.
4. After the connection is completed, follow the instructions in
Table 1 below to check whether the connection is correct and
proceed to the next step.
5. Start the car and do not cranking over 5 seconds.
6. If the engine does not start successfully, check battery level
and if the battery is over 3 bars, wait 3 minutes to try again.
7. After the engine is successfully started, first pull the "smart
clamps" off the device and then remove the clamps from the
car battery.
8. Charge the unit immediately after each use.
Green
Red
Sound
LED
LED
Flash
Flash
On
Flash
Off
Off
Flash
Off
Off
Flash
Off
Off
Off
Flash
On
Off
Flash
On
Off
Flash
On
Off
On
On
Status
Input over voltage protection
No car battery connected
Reverse charge protection
Time out cut off
Wrong connection to high
voltage. Slow flash.
Reverse polarity connection
protection. Fast flash
Short Circuit protection
Over temperature protection
Off
On
Off
On
Off
Off
OVERRIDE function: When the clamps does detect any signals
from car battery, you may use this function for jump start by
push & hold the button on the side of smart clamps for 5s to
activate. Make sure connection is correct before this operation.
WARNING: The OVERRIDE function will void all protections
temporarily, so please make sure the red and black clamps are
correctly connected to a 12V battery.
USB output
1. Connect the USB cable to the USB output port of the device
(3);
2. Short press the "POWER" button (7), USB provides 5V2.4A
output to provide charging for mobile phones/tablets and other
electronic products.
3. The USB output will be automatically turned off after charging
is completed.
4. When the load current exceeds 2.4A, the USB output will be
automatically turned off.
5. The charging time will be more than 8 hours, and the USB
output will be automatically turned off.
Flashlight - work light
1. Press and hold the "POWER" button (7) over 3 seconds to turn
it on.
2. Lighting (2) working mode:
Turning ON: 100% brightness
1st short press: 50% dim light
2nd short press: Slow flash
3rd short press: Flash
4th short press: SOS
5th short press: Close
3. After continuing to work for more than 5 seconds in any
working mode, short press the "POWER" button (7) will turn off
the light directly.
Travel lock
1. Press and hold the "POWER" button (7) over 8 seconds to turn
on the travel lock mode.
2. In this mode, the device will fall into sleep (lock state): short
press the "POWER" button (7) would not turn on the USB output,
work light output or 12V output.
3. To turn off the "travel lock" mode: Press and hold the "POWER"
button (7) again for over 8 seconds to release the device.
ENVIRONMENTAL PROTECTION
This marking shown on the product and its literature
indicates this kind of product mustn't be disposed with
household wastes at the end of its working life in order
to prevent possible harm to the environment or human
health. Therefore the customers is invited to supply to the
correct disposal, differentiating this product from other types
of refusals and recycle it in responsible way, in order to re
- use this components. The customer therefore is invited to
contact the local supplier office for the relative information to
the differentiated collection and the recycling of this type of
product.
P/N: 02524
Low battery protection, recharge
the jump starter to jump start
Correct status for jump start
3
Publicidad
