Fein CCG18-115-10 AS Manual De Instrucciones página 32

en
32
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
The self-start lock prevents the cordless angle grinder
from automatically restarting again after a power inter-
ruption, e.g., after changing the battery. In this case,
switch the power tool off, remove it from the work-
piece and check the application tool. Afterwards, switch
the power tool on again.
Press the locking button only when the motor is
stopped (see page 8).
For best performance, operate the power tool only
with FEIN ProCORE batteries or with ProCORE batter-
ies of AMPShare partners. When using other batteries,
the functionality can be limited.
Additional operating instructions.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
If the power tool shuts off without the switch being
actuated, switch the power tool switch off, remove the
battery and reattach it.
Charge-control Indicator on the Battery (see
page 12).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Transport.
The Li-ion batteries are subject to the Dangerous
Goods Legislation requirements. The user can trans-
port the batteries by road without further require-
ments.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
When working gypsum-containing materials, dust can
settle within the power tool and switch element, which
can harden in connection with humidity. This can
impair the switching mechanism. Blow out the interior
of the power tool via the ventilation slots and the
switch element frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
For FEIN power tools and accessories in need of repair,
please contact your FEIN after-sales service. The
address can be found on the Internet under
www.fein.com.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self:
application tools, auxiliary handle, clamping flanges,
wheel guard
Maintenance and cleaning.
Occasionally clean the ventilation slots and the battery
terminals with a soft, clean and dry brush.
– Do not use chemical substances for cleaning the bat-
tery.
or
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power