Black and Decker PRO Serie Manual De Instrucciones página 37

7. LABELS ON TOOL
The label on your tool may include the following symbols:
Read Instruction Manual
Use Eye Protection
Use Ear Protection
ADDITIONAL SAFETY RULES FOR TABLE SAWS
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the
instructions.
2. OBTAIN ADVICE FROM another qualified person if you are not familiar with the operation of
this machine.
3. FOLLOW ALL WIRING CODES and recommended electrical connections.
4. USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured,
and working correctly.
5. KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK
AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece
pinches the blade. Kickback is dangerous and can result in serious injury.
AVOID KICKBACK by:
A. keeping blade sharp and free of rust and pitch.
B. keeping rip fence parallel to the saw blade.
C. using saw blade guard and spreader for every possible operation, including all through
sawing.
D. pushing the workpiece past the saw blade prior to release.
E. never ripping a workpiece that is twisted or warped, or does not have a
straight edge to guide along the fence.
F. using featherboards when the anti-kickback device cannot be used.
G. never sawing a large workpiece that cannot be controlled.
H. never using the fence as a guide when crosscutting.
I. never sawing a workpiece with loose knots or other flaws.
6. ALWAYS USE GUARDS, SPLITTER, AND ANTIKICKBACK FINGERS whenever possible.
7. REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The
vibration of the machine may cause them to move into the saw blade and be thrown out. After
cutting, turn the machine off. After the blade has come to a complete stop, remove all debris.
8. NEVER START THE MACHINE with the workpiece against the blade.
All manuals and user guides at all-guides.com
GENERAL SAFETY RULES
V Volts
Hz Hertz
min Minutes
Direct current
Class II construction
Safety alert symbol
9. NEVER run the workpiece between the fence and a moulding cutterhead.
10. CUTTING THE WORKPIECE WITHOUT THE USE OF A FENCE OR MITER GAUGE IS
11. HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.
12. CUTTING COMPLETELY THROUGH THE WORKPIECE IS KNOWN AS "THROUGH-
13. AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could
14. KEEP ARMS, HANDS, AND FINGERS away from the blade.
15. NEVER have any part of your body in line with the path of the saw blade.
16. NEVER REACH AROUND or over the saw blade.
17. NEVER attempt to free a stalled saw blade without first turning the machine "OFF".
18. PROPERLY SUPPORT LONG OR WIDE workpieces.
19. NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the
20. TURN THE MACHINE "OFF" AND DISCONNECT THE MACHINE from the power source
21. TURN THE MACHINE "OFF", disconnect the machine from the power source, and clean the
37
A
W
no
.../min Revolutions or reciprocations per minute
KNOWN AS "FREEHAND" CUTTING. NEVER perform "free-hand" operations. Use either
the fence or miter gauge to position and guide the workpiece.
SAWING". Ripping and cross-cutting are through-sawing operations. Cutting with the grain
(or down the length of the workpiece) is ripping. Cutting across the grain (or across the
workpiece) is cross-cutting. Use a fence or fence system for ripping. DO NOT use a fence or
fence system for cross-cutting. Instead, use a miter gauge. USE PUSH STICK(S) for ripping a
narrow workpiece.
cause a hand to move into the blade.
machine is running.
before installing or removing accessories, before adjusting or changing set-ups, or when
making repairs.
table/work area before leaving the machine. TURN THE SWITCH IN THE "OFF" POSITION.
Amperes
Watts
Alternating Current
No load speed
Earthing terminal