Publicidad
Idiomas disponibles
Idiomas disponibles
EN
LAICA Tap filter
6) To install the connector with the M adapter, proceed as follows:
Remove the fastening ring from the connector and take the L adapter with Ø21 mm diameter, then assemble the
-
three pieces as described in figure 6A, 6B and 6C.
6A
-
Loosen the fastening band with a flat head screwdriver and remove the smaller seal inside the adapter M (fig.
7A, 7B).
7A
Choose the best seal: only the one with the largest diameter (fig. 8A) or both with one inserted inside the other,
-
pressing firmly and taking extra care over the direction in which they are inserted (fig. 8B).
8A
8B
-
Install the adapter M on the tap and tighten the fastening band using a flat
head screwdriver to secure it firmly to the tap (fig. 9A and B).
9A
9B
7) Remove the HYDROSMART™ METAL STOP filter from its packaging and rinse it under running water. Now hook
the filter to the connector as shown in figure 11A, 11B, 11C.
11A
11B
03
6B
6C
7B
-
Screw the connector onto
the ring (fig. 10).
10
11C
03
12
Instructions and guarantee
ACTIVATING THE FILTER LIFE MANUAL INDICATOR
Turn the manual indicator of the filter life D to set the start
month of using the filter. The reference month must be lined
up with the O line.
SMART FILTRATION SYSTEM – FREE LAICA HOME
WELLNESS APP - USE
List of compatible devices:
• iOS: iPhone with version 10 operating system.
• For devices with Android™ operating system: from
version 6.0 (Marshmallow).
By adding the HYDROSMART™ METAL STOP filter to the
free "Laica Home Wellness" app, you can receive automatic
notification on your smartphone when to replace the filter.
1. Install the free "Laica Home Wellness" app on your
smartphone.
2. Start the app and enter the "FILTER" section from the
main screen.
3. Add the HYDROSMART™ METAL STOP FILTER by
pressing the "+" key. It is possible to add the filter by
scanning the QR code printed on the upper part of the
filter or manually by pressing the "Select manually"
button.4. The app adds the filter and automatically
prompts the replacement date.
To optimise the effective duration of the filter based on
the water treated, you can select the chlorine level in
your water supply. To use it properly, request further
information from your water supplier or carry out a
preliminary assessment of the local water supply.
5. Save the settings by pressing the " " key.
6. When the filter replacement date is reached, the
notification to replace it will appear on your smartphone.
The notification is also sent to the email address given
during registration.
• To scan the QR code on the upper part of the
filter, you must authorise the app to access
to your smartphone camera.
• To receive notifications when to replace the
filter, you must enable the settings on your
smartphone.
• To replace the filter, you can add a new one
by scanning the QR code printed on the
upper part of the filter or by updating the
expiry date by clicking on the "Filter expired"
button (click to replace)".
USING THE FILTERING SYSTEM
Activating the LAICA HYDROSMART™ METAL STOP
filter:
When first used and every time the HYDROSMART™ METAL
STOP filter is changed, turn the tap on and allow the water
to flow through the filter for several minutes (at least 4-5
minutes) to correctly activate the materials of which the
filter is composed.
This water can be used for watering plants. If the LAICA
filtering system has not been used for 24 hours or more,
allow the water to flow for 30-60 seconds before using the
filtered water again.
CAUTION:
- To guarantee the performance characteristics of the
filtering system, it is recommended to filter cold water
only.
- The flow of water at a temperature higher than 50°C
through the connector may cause permanent damage.
The flow of water at a temperature higher than 35°C
through the filter may cause permanent damage.
- To adjust the water flow properly, open the tap slowly.
The LAICA filtering system has 3 different ways of
dispensing the water which can be selected with the
selector C:
1) Filtered water for
drinking, washing
fruit and vegetables,
cooking and carry out
all routine tasks with
safe, pleasant tasting
water.
2) Unfiltered water with
spray head.
3) Unfiltered water with
continuous stream.
REPLACING THE FILTER
To replace the filter, turn the filter anticlockwise and remove
it by pulling it outwards (fig. 12A, 12B, 12C).
12A
12B
12C
03
Replace it with a new filter repeating the steps described
in point 7 of the paragraph "PREPARING THE FILTERING
SYSTEM", "ACTIVATING THE FILTER LIFE MANUAL
INDICATOR" and "USING THE FILTERING SYSTEM -
Activating the HYDROSMART™ METAL STOP filter".
To achieve the best results and guarantee the safety of the
filtering system, we recommend replacing the filter every 4
months or 1200 litres of filtered water.
CARE AND MAINTENANCE
Make sure your hands are clean during maintenance work
on the filtering system.
Regularly clean the outer part of the connector with a damp
13
EN
03
Publicidad
