Publicidad
IMPORTANT - READ CAREFULLY AND
GB
KEEP FOR FUTURE REFERENCE
TO ASSEMBLE COT
NOTE: Do not fully tighten screws until cot is fully assembled.
1 - To correctly position the dropside (C) during assembly place the 'PUSH' sign on the outside and to
the bottom of the construction.
Use two long screws (Q) to fix both the top plastic corners (U) to dropside (C).
Use two long screws (Q) to fix both bottom plastic corners (T1 & T2) to dropside (C).
Note: Make sure that the spring clip (H) on the left and right bottom corners are orientated as shown
with the long face facing outwards.
2 - Use four long screws (Q) to fix top plastic runners (N) to cot ends (A). Note which way, the part
should be fixed.
Use four screws (P) to fix bottom metal runners (M) to cot ends (A). Note which way, the part should
be fixed.
3 - Use four long screws (E) with plastic washers (R), to attach fixed side (B) through cot ends (A).
Ensure dropside runners face into cot.
4 - Use a hammer and eight short screws (L) to fix plastic mouldings (K) onto base (D).
NOTE: Ensure that all four plastic moulding (K) are firmly fixed onto base (D).
5 - Use four short screws (F) with plastic washers (R), to fix base (D) to cot ends (A).
Gently tighten all screws, taking care not to overtighten.
6 - With spring clips (H) at bottom of dropside (C), carefully locate the four slides on corners of dropside
(C) into four runners on cot ends (A).
ATTENTION - the "PUSH" label must be facing outwards.
Gently pull spring clips (H) towards you, and raise dropside (C) into closed position. It will engage
automatically.
Screw the two rubber stops (G) through the lower metal runners and tighten with the screws (S) and
nuts (J).
DROPSIDE OPERATION
-
To lower dropside, raise side slightly, press with leg at centre of bottom rail and lower side until it
locks automatically. Check that it is correctly engaged.
-
To raise the drop side slightly lift it, and while you maintaining this action, press with your leg at
center of bottom rail and raise side until it engages automatically. Check that the side is perfect
secure.
WARNING
Warning: Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires,
gas fires, etc. in the near vicinity of the cot.
Warning: Do not use the cot if any part is broken, torn or missing and use only spare parts approved by
the manufacturer.
Warning: Do not leave anything in the cot or place the cot close to another product, which could provide
a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
Warning: Do not use more than one mattress in the cot.
NOTE: Of the base height positions the lowest is the safest and is the only one you should use when
your child can sit up.
If you leave your child unattended in the cot, always make sure dropside is in the highest position.
Thickness of the mattress shall be such that the internal height (surface of the mattress to the upper
edge of the cot frame) is at least 500 mm in the lowest position of the cot base and at least 200 mm in
the highest position of the cot base.
NOTE: Fig.7 -
The Cot End (A) is marked with two small holes (X) and (Y). When the base is in the
highest position the top of mattress used should be bellow this mark (X) and when the base is in the
lowest position the top of the mattress used should be bellow this mark (Y).
The minimum size of mattress to be used is 120 x 60 cm.
The length and width shall be such that the gap between the mattress and the sides and ends does not
exceed 30 mm.
Before using the cot ensure all assembly fixings are properly tightened, and remember to regularly
check that they remain
Loose screws can pinch parts of the body or catch clothing (string or ribbons on dummies etc.), and
present a danger of strangulation.
When the child is able to climb out of the cot, with the mattress base on it's lowest positon and the
dropside raised, the cot shall no longer be used for that child.
COT CARE
If possible, do not place your cot next to a radiator or hot air vent.
The use of abrasive cleaners is not recommended. Simply wipe clean and buff with a soft dry cloth.
Careless handling or movement of wooden furniture can damage it.
Publicidad
