EnGLIsh
2. When changing accessories, always disconnect air supply to
avoid injury.
3. When job is completed, turn off the air compressor and
store the air tool after lubrication.
Operating Instructions
1. Securely fit the socket or attachment to the impact wrench.
2. Place the Forward/Reverse and speed control switch in the
correct position for tightening or loosening the fastener.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental actuation
can cause injury.
Your Mac Tools power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
C
Lubrication
CAUTION: This air tool requires lubrication BEFORE initial
use, also before and after each additional use.
WARNING: Keep out of the reach of children. If air
tool oil is ingested, do not induce vomiting, call a
doctor immediately.
WARNING: Any excess oil in the tool is immediately
expelled from the exhaust port. Always direct exhaust port
away from people or objects.
Air tools require lubrication throughout the lifetime of the tools.
This power tool uses compressed air as a power source. The
compressed air contains moisture that will rust the components
inside of the tools, therefore lubrication is required daily. Failure
to lubricate the air tool properly will dramatically shorten the life
of the tool and will void the warranty
Always use an air line lubricator with this tool. After every eight
hours of operation, if a lubricator is not used on the compressed
air network, inject 1/2 to 1 cc of approved air tool oil (Mac Tools
part #PO32) through the tool's inlet connection.
After every forty-eight hours of operation, or as experience
indicates, inject about 4 cc of approved pneumatic grease (Mac
Tools part #PNG16) into the grease fitting.
to lubricate the air tool manually:
1. Disconnect the tool from the air supply source, place the air
inlet face up.
2. Depress the trigger and place about 5 to 10 drops (0.25 to
0.5 ml) of air tool oil into the air inlet.
nOtE: use saE #10 weight oil if air tool oil is not available.
20
3. Remove accessory, connect the tool to an air source, then
cover the exhaust end with a towel and run tool for 2 to
3 seconds.
to lubricate internal mechanism:
Locate the grease fitting in the back of the tool. Inject 4 cc's of
MAC tools approved impact grease into the fitting every 3-6
months depending on use.
nOtE: check the speed and make a simple check of the
vibration level after each service.
Storage
Store pneumatic tool and accessories in a dry, safe place. The air
tool must be lubricated before storing.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Disposal
The pneumatic tool, accessories, and packaging should be
sorted for environmental-friendly recycling.
When your unit is no longer suitable for use, please return it to a
specialist store or a Mac Tools service shop.
Customer Service
We at Mac Tools are committed to our customers, please
reference the phone numbers on the backpage for a direct
contact to one of our customer technicians. They will be more
than happy to help with any service or warranty questions you
may have about your power tool
WARRANTY
We warrant that this tool shall be free from manufacturing
defects for a period of TWO YEARS from the original purchase
date. Our obligation to the original purchaser shall be limited to
repairing or replacing, at our expense (not including shipping
charges) a defective tool if returned by the original purchaser
within two years from the date of purchase, all incoming
shipping charges prepaid. THIS WARRANTY DOES NOT COVER
DEFECTS OR DAMAGES TO THE TOOL (i) after the warranty
period expires; (ii) resulting from misuse or abnormal operat ion
; (iii) resulting from a failure to properly lubricate, maintain or
operate the tool; or (iv) resulting from any repair or maintenance
services performed by any party other than Mac Tools.