Power Button
Standby mode: As you plug the appliance into the power supply, it will
beep and all the indicators will flash on and then off. The power indicator
will be on in the top right-hand corner of the LED display. Your appliance
is now in standby mode.
Turning on: Press the power button to turn on the appliance. Its
default mode will be automatic mode, with high wind speed and
humidity of 60%. The appliance will start up in the mode selected
when the unit was last used.
Turning off: Press the power button to turn the appliance off.
Unplug the appliance if it will not be used for extended periods.
Modes
Mode button: Press the mode button to cycle between different
modes. The corresponding indicator will light up.
Auto mode: In this mode, when the environment's humidity exceeds
the set humidity by more than 3%, the fan will automatically turn
on and 3 seconds later the compressor will start working. The
appliance will automatically turn off if the environment's humidity
is 3% lower than the set humidity. You can adjust the fan speed and
humidity settings in this mode.
Continuous drying mode: In this mode, the appliance will be on and
the set humidity cannot be changed.
Sleeping mode: In this mode, after 10 seconds all indicators will
turn off and the wind speed will change to low. Touch any button to
bring the indicator lights back on. In sleep mode, error codes will not
be displayed, and the wind speed is not adjustable. The humidity
settings are still adjustable.
Humidity
While the appliance is on, in auto mode or sleep mode, press the
Button
humidity button to cycle through the humidity settings. These will
display on the display panel in 5% increments, between 30% and
80%. When you reach your target room's humidity, it will set after 5
seconds of no other buttons being pressed.
Long press the humidity button to view the current room
temperature on the LED display. After 5 seconds, the LED display will
revert to the current humidity.
LED display
The numbers on the LED display will show the current humidity of
the room, the hours set when setting a timer, or the temperature
when the humidity button is held down. The icons around the
numbers will indicate the fan setting, mode, and if the child lock is
on.
Timer Button
Press the timer button to cycle between 1 – 24 hours, in increments
of one hour. The hours set will be displayed on the LED display.
When the LED display reads '00', the timer is turned off, and the
indicator will turn off.
While the appliance is on, set the timer to turn the appliance off.
While the appliance is in standby mode, set the timer for the
appliance to turn on.
10 of 80 | English
Fan Speed
In auto mode, press the fan speed button to switch between high
Button
and low fan speed. The corresponding indicator will light up.
Lock Button
Long press the lock button to activate child lock. All buttons on the
appliance will be locked and the child lock indicator will be on.
To remove child lock, press the lock button again. The indicator will
turn off.
Child lock will be turned off when the appliance restarts.
Note: The appliance will start up in the mode selected when the unit
was last used. The appliance will not start if the water tank is not
fitted in the unit correctly. The compressor's start is delayed by 3
minutes after the start of the fan.
Colour Display
The light will display different colours according to the ambient
humidity of the environment:
•
Blue – Below 45%
•
Green – Between 45% and 65%
•
Red – Above 65%
Note: The light will also be red if any of the error codes are
displayed on the LED display. See the 'error codes' section for more
information.
ERROR CODES
― ―
ERROR CODE CAUSE
E0
The wiring has malfunctioned.
E2
The humidity sensor is unable
to detect the humidity of the
environment.
LO
The humidity of the
environment is below 20%
HI
The humidity of the
environment is above 90%
CL
The temperature of the
environment is below 5°C
CH
The temperature of the
environment is above 38°C
SOLUTION
Contact Pro Breeze Customer Care by
sending an email to help@probreeze.com
or via our website www.probreeze.com
The appliance will automatically shut
down to prevent damage. Move the
appliance to a more suitable environment
and manually restart it.
English | 11 of 80