Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EN
USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
DOCKING STATION INSTALLATION
•
Unpack the docking station, plug and installation leaflet.
•
Select the location for the docking station and ensure that there is no pipework
(gas, water or air), electrical cables, wires or ductwork directly behind the
mounting location.
•
Follow the instructions on the installation leaflet.
•
Click the attachments into place.
•
Place the appliance in the docking station.
•
Plug in the docking station and turn on to charge.
•
Your appliance will need to be fully charged before first use.
The docking station must be mounted in accordance with regulations and
applicable codes/standards (state and local laws may apply).
Dyson recommends the use of protective clothing, eyewear and materials when
installing the docking station.
VACUUMING
•
Remove the appliance from the docking station.
•
Check that the underside of the cleaner head or tool is clean and free from foreign
objects that may cause damage.
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
The brush bar on the appliance can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorised floor tool and consulting with your
flooring manufacturer.
LIGHTS DURING CHARGING
Charging, low charge
Charging, medium charge
Charging, nearly full
Fully charged
LIGHTS DURING USE
High level of charge
Medium level of charge
Low level of charge
Empty, needs charging
LIGHTS DIAGNOSTICS
Battery fault-call Dyson Helpline
Main body fault-call Dyson Helpline
Charger fault-call Dyson Helpline
36
FILTER AND BLOCKAGE INDICATOR LEDS
Blockage indicator
Filter unit not fitted correctly
Filter unit requires washing
See battery section
EMPTYING THE CLEAR BIN
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•
Ensure that the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
•
Avoid pulling the 'ON' trigger when emptying.
•
Remove the wand by pressing the red wand release button and pulling away from
the bin.
•
To release the dirt:
– Hold the appliance with the bin in a downwards position.
– Firmly push the red bin release button.
– The bin will slide down, cleaning the shroud as it goes.
– The bin base will then open.
– The bin base will not open if the red button is not pushed down fully.
To minimise dust/allergen contact when emptying, encase the clear bin tightly in a
plastic bag and empty. Remove the clear bin carefully from the bag. Seal the bag
tightly, dispose as normal.
CLEANING THE CLEAR BIN (OPTIONAL)
If it is necessary to clean the clear bin:
•
Follow the instructions in the 'Emptying the clear bin' section.
•
Press the red button located on the bin runner to release the bin and slide the bin
off the runner.
•
Clean the clear bin with a damp cloth only.
•
Ensure that the clear bin and seals are completely dry before replacing.
•
To refit the clear bin:
– Insert the spine on to the bin runner.
Close the clear bin by pushing the bin base upwards until the clear bin and bin base
click into place.
The clear bin is not dishwasher safe and the use of detergents, polishes or air
fresheners to clean the clear bin is not recommended as this may damage
your appliance.
FILTER AND BLOCKAGE INDICATOR LEDS
Your appliance has two indicator lights that will help alert you that simple
maintenance steps are needed.
•
The filter indicator will flash intermittently when the filter unit is not fitted correctly.
Follow the instructions on how to refit the filter unit in the 'Washing the filter unit'
section.
•
The filter indicator will light continuously when the filter unit needs washing. Follow
the instructions on how to wash the filter unit in the 'Washing the filter unit' section.
•
The blockage Indicator LED will light if there is a blockage. Follow the instructions
on how to clear blockages in the 'Looking for blockages' section.
WASHABLE PARTS
Your appliance has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE FILTER UNIT
Check and wash the filter unit, according to the instructions, to
maintain performance.
•
Remove the filter unit by twisting anticlockwise to the open position. Gently pull
away from the appliance.
•
Wash the inside of the filter unit first; hold it upright under the cold water tap and
agitate using a rotating motion.
•
Wash the outside of the filter unit; fill the unit with cold water, place your hand over
the open end and shake gently.
•
Repeat washing the inside and outside of the filter unit until the water runs clear.
•
Gently tap the filter unit to remove any excess water and leave to dry with the filter
end down.
•
Leave the filter unit to dry completely for a minimum of 24 hours.
•
Check that the filter unit is completely dry.
•
To refit, return the filter unit to the open position and twist clockwise until it clicks
into place.
The filter unit may require more frequent washing if vacuuming fine dust or using
mainly maximum suction.
Do not put the filter unit in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
Publicidad
Tabla de contenido
