Publicidad
Idiomas disponibles
Idiomas disponibles
9.7 Moving the transport handle (5) to the transport
position (fig. 11)
The transport handle is already pre-mounted on the
splitter and is fastened in the working position. Loosen
the pin and move the transport handle (5) down until
the pin can be inserted into the next hole to fix the posi-
tion of the transport handle. See steps 1 - 3.
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!
10. Initial operation
Make sure the machine is completely and expertly as-
sembled. Check before every use:
• The connection cables for any defective spots
(cracks, cuts etc.).
• The machine for any possible damage.
• The firm seat of all bolts.
• The hydraulic system for leakage.
• The oil level.
• Functional check
Checking the oil level (Fig. 15)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage the
oil pump. The level of oil must be checked when the
riving knife is pulled back. If the oil level is at the lower
notch, then the oil level is at a minimum. Should this be
the case, oil must be immediately added. The upper
notch indicates the maximum oil level. The machine
must be on level ground. Screw in the oil dipstick fully,
to measure the oil level.
E- Motor
Check the running direction of the motor. If the splitting
arm is not in the top position, bring the splitting blade in
the top position, using the return bracket or handles. If
the splitting arm is already in the top position, activate
the splitting mechanism by moving both levers down.
This will move the splitting arm down. If the splitting
blade does not move despite activation of the handles
or return bracket, immediately turn off the machine.
Turn the pole reversing unit in the plug-in module (Fig.
11 + 12) to change the rotational direction of the motor.
Never let the motor run in the wrong direction!
This will inevitably destroy the pump system and
no warranty claim can be made.
28 | GB
Functional test
Test the function before every use.
Action:
Push both handles
towards below.
Let one handle loose,
then the other.
Push return bow
upwards
Warning!
Loosen the filling screw (Fig. 15) before commis-
sioning. Never forget to loosen the filling screw!
Otherwise, the air in the system will constantly
be compressed and decompressed with the re-
sult that the seals of the hydraulic circuit will be
destroyed and the wood splitter can no longer be
used. In this case, the seller and the manufacturer
will not be liable to warranty services.
Switching on and off (14)
Press the green button for switching on.
Press the red button for switching off.
Note: Check the function of the ON/OFF unit before
every use by switching on and off once.
Restarting safety in case of current interruption
(no-volt release).
In case of current failure, inadvertent pulling of the
plug, or a defective fuse, the machine is switched off
automatically. For switching on again, press anew the
green button of the switch unit.
Using the retaining claw (Fig. 12)
The height of the claw can be set at various stages to
suit the length of the wood.
Splitting (Fig. 13)
• If the outside temperature is below 5°C, let the ma-
chine run idle for about 5 minutes so the hydraulic
system reaches its operating temperature. Place the
log under the splitting blade vertically.
Caution: The splitting blade is very sharp. Risk
of injury!
• Push the retaining claw (13) onto the wood to be
split.
• When you push both operating levers (2 +12) down,
the splitting blade goes down and splits the wood.
www.scheppach.com
Result:
Splitting knife goes down
to approx. 20 cm above the
table.
Splitting knife stops in the
desired position.
Splitting knife returns to
upper position
Publicidad
