Publicidad
Idiomas disponibles
Idiomas disponibles
Step 6:
Slowly bring it to a 90° angle to begin the cut.
The base guide should be flush to the material
surface. For all materials (EXCEPT cutting
around outlet boxes in drywall*), steer the tool in
a clockwise direction with slow, steady pressure
to make the cut.
Step 7:
After completing your cut, turn off the tool and
carefully remove it from the material.
Do not attempt to use this tool
WARNING
!
to make cut-outs around any
fixture or opening which has live electrical wires,
or any wall which may have live electrical wiring
behind it, as the Zip Bit could conduct current to
the tool, creating an electrocution hazard for the
operator. Shut off breakers or remove fuses to
disconnect the circuit. Always hold the tool by
its thermoplastic housing, and always wear eye
protection when operating a Spiral Saw™
power tool.
NOTE: Because of the rotating cutting action of
the Zip Bit, there will be a slight pull when
cutting. The slower you cut, the more control
you have. Excessive pressure or fast cutting
will cause excessive heat and may shorten the
life of the Zip Bit.
NOTE: When cutting on a vertical surface,
avoid ending your cut at the bottom of the hole.
If possible, start and end your cut at the top so
the scrap part will not drop onto the rotating Zip
Bit. Turn the tool off and remove it from the
material.
-8-
Maintenance
Service
Preventive maintenance
WARNING
!
performed by unauthorized
personnel may result in misplacing of
internal wires and components which could
cause serious hazard. Roto Zip Tool
Corporation is the only authorized repair center
for their tools. Contact the Customer Service
department, toll free in the U.S. and Canada, at
1-877-768-6947, Monday through Friday
between 8am-4:30pm CST, for further
instructions.
Accessories
Use only Roto Zip Tool
WARNING
!
Corporation's recommended
accessories with this tool. Accessories that
may be suitable for one tool, may become
hazardous when used on another tool.
If an extension cord is
WARNING
!
necessary, a cord with
adequate size conductors that is capable
of carrying the current necessary for your
tool must be used. This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles
.
Zip
®
Bits
Roto Zip Tool Corporation's patented line of
versatile Zip Bits and accessories provide you
with the flexibility to quickly move from one
material to another and one job to another,
without the hassle of changing tools.
ZBSC5
RZ125
RZ250
GP10
ZB10
ZBWD8
FBR250
Where Can You Buy Accessories?
The location where you purchased your tool should also carry Roto Zip Tool Corporation's full line of
accessories. Our products are available at most home improvement centers and hardware stores. If
you are looking for a source, please call our Customer Service representatives Monday through
Friday between 8am - 4:30pm (CST) at 1-877-768-6947 (toll free in the U.S. and Canada).
Cleaning
To avoid accidents always
WARNING
!
disconnect the tool from the
power supply before cleaning or performing
any maintenance.
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
attempt to clean by inserting pointed objects
through openings.
Certain cleaning agents and
CAUTION
!
solvents damage plastic
parts. Some of these are: gasoline, carbon
tetrachloride, chlorinated cleaning solvents,
ammonia and household detergents that
contain ammonia.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
Cord Size in A.W.G.
Wire Sizes in mm
Tool's
Ampere
Cord Length in Feet
Cord Length in Meters
Rating
25
50
100 150
15
30
3-6
18
16
16
14
.75 .75 1.5
6-8
18
16
14
12
.75 1.0 2.5
8-10
18
16
14
12
.75 1.0 2.5
10-12
16
16
14
12
1.0 2.5 4.0
12-16
14
12
—
—
—
—
NOTE: The smaller the gauge number, the heavier
the cord.
-9-
2
60
120
2.5
4.0
4.0
—
—
—
Publicidad
