LUND 68480 Manual De Instrucciones página 9

Clean the product according to the instructions specifi ed in the "Product Maintenance" section.
The drive housing must be placed on a level, fl at, hard and stable surface. All drive housing stands should be in contact with the
ground.
Replace the lid on the drive base and check that it returns to its original position immediately and automatically when the switch
is pressed and released. Then connect the appliance to the power supply and check that it starts when you press and hold the
power switch and stops when you release the pressure on the power switch. The appliance has a safety feature which prevents
the grinder from starting if the lid is not installed correctly.
Warning! The blade may still rotate for some time after releasing the pressure on the switch.
Do not remove the lid until the blade has come to a complete stop and the power cord has been unplugged from the socket.
Product operation
Make sure that the power cord is unplugged from the socket.
Remove the lid and pour the products to be ground into the chamber. Do not exceed the maximum grinder capacity specifi ed in
the table. Mount the lid, connect the mill to the power supply. Hold the housing with one hand and apply pressure on the lid with
the other. Then press and hold the switch.
This will start the grinding process. The degree of fi neness can be controlled with the length of the grinding process. The longer
the grinding time, the more fi nely the food will be ground.
Do not exceed 30 seconds of continuous operation, after which you must wait at least another 30 seconds for the grinder to cool
down. Overheating of the grinder may lead to damage to the appliance or cause fi re or electric shock. In addition, ground products
can change their properties when exposed to excessive temperatures.
When grinding is complete, release the pressure on the switch, wait until the blade has stopped rotating completely, and then
unplug the power cord from the socket. Remove the lid and tilt the grinder to pour out the ground products.
CAUTION! If the appliance begins to vibrate after switching it on, if it makes an unusual sound, or shows any other signs of mal-
function, switch it off immediately, unplug it, and check for the cause of the malfunction.
Product maintenance
CAUTION! Every time before cleaning, switch off the cutter, unplug the power cord plug from the socket, wait for the appliance to
cool down and then proceed with maintenance.
Use only mild kitchen cleaning agents to clean it. It is forbidden to use abrasive cleaning agents, e.g. cleaning powder or milk, or
agents containing corrosive substances. Do not use any solvents, petrol or alcohol to clean the product.
Dilute the cleaning agent with water, according to the instructions supplied with the agent. Then, apply it on a soft cloth and clean
the drive housing on the outside.
Remove any residues of the cleaning agent with a soft cloth slightly soaked in clean water. Then, dry all surfaces with a dry soft cloth.
CAUTION! The drive housing is not designed for water jet cleaning. Do not immerse the drive housing in water or other liquid.
Clean the inside of the chamber and the blade with a soft brush or cloth. Clean with a cloth slightly soaked in water, and then
thoroughly dry the inside of the chamber and the blade.
Warning! Special care should be taken when cleaning the blade and the inside of the grinding chamber. The blade has sharp
edges and can cause injury. It is recommended to use protective gloves when cleaning.
The lid can be cleaned with a jet of running water. It is not recommended to clean the lid in dishwashers or with a high pressure
water jet as the lid surface may matt.
All the components must be thoroughly dried, before reusing the product.
Transport and storage
Before commencing storage or transport of the product, clean it thoroughly from food residues.
If stored, keep the product indoors, and make sure it is not exposed to dust, dirt, or moisture. It is recommended to store the
product in its original packaging.
The 68481 model grinder's power cord can be rolled up in the base socket (II). The cable must be completely unfolded before use.
TECHNICAL DATA
Parameter
Catalogue No.
Rated voltage
Rated frequency
Rated power
Grinding chamber capacity
Insulation class
Weight
Duty
O R I G I N A L
GB
Unit
[VAC]
[Hz]
[W]
[kg]
I N S T R U C T I O N S
Value
68480/68481
220-240
50/60
150
70
II
0.6
S2: 30 s
9