English
USB Charging Ports (Fig. A, G)
The DWST08050 is equipped with one USB
USB-C
18
charging ports. The USB
2.0 amps and the USB-C
total current.
nOTE: The current delivered to the device is dependent
upon the user's device and user's chosen cable.
nOTE: Do not plug in devices that exceed the output ratings
on the DWST08050 rating label. Doing so will shorten the
charger's useful life.
Using the USB port:
1. Open the storage door to gain access to the USB
charging port
17
.
2. Insert a USB plug into USB charging port
power or charge your device.
Using the USB-C port:
1. The USB-C charging port
the box, above the power cord
2. Pull back the USB-C port cover
charging port
18
.
3. Insert a USB-C plug into USB-C charging port
supply power or charge your device.
nOTE: Ensure the port cover is reinstalled after use.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before making
any adjustments or removing/installing attachments
or accessories. An accidental start‑up can cause injury.
Your D
WALT product has been designed to operate over
e
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
care and regular cleaning.
Storage and Transportation
•
Always store disconnected from power supply!
•
Avoid using the product outdoors or transporting in an
open vehicle if there is noticeable damage to the sealing
gasket or plastic exterior.
•
Avoid continuous exposure to rain or other precipitation
if stored outdoors or on a vehicle, or if transported in an
open vehicle.
•
Store the charger in a place that is as cool and dry
as possible.
•
Store the charger in a place where it cannot be accessed by
children or unauthorized persons.
•
Check the charger for damage before use after long periods
of storage.
10
17
and one
17
delivers up to
18
delivers up to 3.0 amps of
17
to supply
18
is located on the back of
8
.
7
to reveal the USB-C
18
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this product could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com
Tool Connect™ Chip (Fig. H, I)
Optional Accessory
to
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ chip
application for your smart device (such as a smart phone
or tablet) that connects the device to utilize the mobile
application for inventory management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Insert the Tool Connect™ Chip
empty pocket
2. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws
tighten the screws.
3. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs, and brush inspection and replacement,
when applicable) should be performed by a D
factory service center or a D
center. Always use identical replacement parts.
WALT recommended
e
WALT call 1‑800‑4‑D
e
21
communicates with an optional
21
into the
23
.
WALT authorized service
e
WALT
e
22
and
WALT
e