Hikmicro CHEETAH Serie Guia De Inicio Rapido página 111

cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-003 (B)/NMB-003(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, CNR-102
énoncée dans un autre environnement.
KC
B급 기기: 이 기기는 가정용(B급) 전자파적합기기로써 주로 가정에서
사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical safety
regulations.
Transportation

Keep the device in original or similar packaging while transporting it.

Keep all wrappers after unpacking them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
 Transportation without the original wrapper may result in damage on the device
and the company shall not take any responsibilities.

Do not drop the product or subject it to physical shock. Keep the device away from
magnetic interference.
Power Supply

The input voltage for the device should meet the Limited Power Source (5 VDC, 2 A)
according to the IEC61010-1 or IEC62368 standard. Please refer to actual products and
technical specifications for detailed information.
 The power source should meet limited power source or PS2 requirements according
to IEC 60950-1 OR ICE 62368-1 standard.

Use the power adapter provided by qualified manufacturer. Refer to the product
specification for detailed power requirements.

Make sure the plug is properly connected to the power socket.

DO NOT connect multiple devices to one power adapter, to avoid over-heating or
fire hazards caused by overload.
Battery

Improper use or replacement of the battery may result in explosion hazard. Replace
with the same or equivalent type only. Dispose of used batteries in conformance with
the instructions provided by the battery manufacturer.

Use the battery provided by qualified manufacturer. Refer to the product
specification for detailed battery requirements.
 Make sure the battery temperature is between 0°C to 45°C (32°F to 113°F) when
charging.

For long-term storage of the battery, make sure it is fully charged every half year to
ensure the battery quality. Otherwise, damage may occur.

The built-in battery cannot be dismantled. Please contact the manufacture for repair
if necessary.

Batteries of improper size cannot be installed, and may cause abnormal shutdown.
 The battery cannot be charged with external power source directly.

Confirm there is no flammable material within 2 m of the charger during charging.

DO NOT place the battery near heating or fire source. Avoid direct sunlight.

DO NOT place the battery in the reach of children.

DO NOT swallow the battery to avoid chemical burns.
Maintenance

If the product does not work properly, please contact your dealer or the nearest
service center. We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.
 Wipe the device gently with a clean cloth and a small quantity of ethanol, if
necessary.

If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the device may be impaired.

Clean the lens with soft and dry cloth or wiping paper to avoid scratching it.

It is recommended to reboot the device every 2 hours when using it to ensure the
device performance.
Using Environment
 Make sure the running environment meets the requirement of the device. The
operating temperature shall be -30 °C to 55 °C (-22 °F to 131 °F), and the operating
humidity shall be 95% or less, no condensing.

Place the device in a dry and well-ventilated environment.

DO NOT expose the device to high electromagnetic radiation or dusty environments.

DO NOT aim the lens at the sun or any other bright light.

When any laser equipment is in use, make sure that the device lens is not exposed
to the laser beam, or it may burn out.
 Avoid equipment installation on vibratory surface or places subject to shock (neglect
may cause equipment damage).

This device can only be safely used in the region below 2000 meters above the sea
level.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.
109