Hilti NCR 060 II-A22 Manual De Instrucciones página 20

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Additional safety instructions for crimping tools
Safety when working in the vicinity of electrical installations
Invariably, before work commences a risk assessment has to be carried out, and the necessary protective
measures have to be implemented.
All personnel involved in work in the vicinity of electrical installations must have received instruction
concerning the applicable safety requirements, safety regulations and company operating procedures
Working procedures are divided into three different procedures: dead working, live working, working in the
vicinity of live parts. All these procedures are based on the use of protective measures against electric
shock and/or the effects of short-circuits and arcing. For further details refer to EN 50110 and any national
requirements and practices. It shall be verified that all methods and tools chosen are suitable for the
installation to be worked on.
▶ For all work on electrical installations, observe the valid international, national and local laws and
regulations, such as EN 50110.
Personal safety
▶ Comply with the country-specific standards and safety instructions for operation of crimping tools and
all work on, with or in proximity to electrically live equipment and lines.
▶ Persons who work in the vicinity of live lines must receive regular instruction and training.
▶ Use the crimping tool only when it is in technically faultless condition.
▶ Never tamper with or modify the crimping tool in any way.
▶ If you notice oil escaping, cease working with the tool and consult Hilti Service. Immediately remove the
leaked oil.
16 English 2207049
*2207049*