Publicidad
Idiomas disponibles
Idiomas disponibles
UNPACKING
1.
Remove ash vacuum from carton.
2. Check the appliance for possible shipping damage
and make sure all the parts are included. See Getting
Started. If any damage is found immediately contact
the manufacturer at 1-800-251-0001.
ASSEMBLING FOR VACUUMING
1.
Unlock the latches and remove the power head lid.
2. Attach the filter set to the bottom of the head.
Reattach the power head to the container and secure it
with the latches.
3. Insert the metal tube into the flexible hose and insert
the other end of the flexible hose into the vacuum port
and rotate 1/4 turn counter-clockwise. See Figure 1A
and 1B.
A
Figure 1
ASSEMBLING FOR BLOWING
1.
Insert the metal tube into the flexible hose and insert
the other end of the flexible hose into the air outlet on
top of the power head lid and turn counter-clockwise
to lock. See Figure 2.
Figure 2
OPERATION
1.
Plug in the power cord and turn the vacuum cleaner
power switch ON.
2. When the container is full or it feels difficult to vacuum
more dust, the cartridge filter needs to be taken out
and cleaned.
3. When vacuuming the fireplace ash, the ash
temperature must be below 100˚°F (40˚°C). Do not
vacuum the ashes if fire is not extinguished!
Cleveland Ironworks, Inc.| Ash Vacuum Cleaner
B
4. Run the unit for 30 seconds after you have finished
cleaning your stove or fireplace to ensure all materials
are safely captured in the container.
5. When finished, turn the power switch OFF.
6. Pull out power cord from outlet and roll up. Remove
flexible tube.
7.
Remove power head and empty and wash out vacuum
container. Dry out container with rag.
WARNING: ALWAYS DISCONNECT THE PLUG FROM
THE POWER OUTLET BEFORE REMOVING THE POWER
HEAD FROM CONTAINER.
8. Remove and clean filter as described below in
Maintenance section.
IMPORTANT: Vacuuming materials, which appear to
have cooled down, may still be very hot inside. Hot ash
particles may ignite again with airflow. Wait until the fire is
extinguished and the ashes have cooled down before you
begin with the cleaning. It is not recommended to quickly
extinguish the fire with water. Please make sure that ovens
are cold before you vacuum to clean ovens. Temperature
exceeding 100˚°F (40˚°C) may damage the vacuum cleaner
and the components included. Continuously check tubes,
ash filter, and vacuum cleaner for excessive temperatures
during the vacuum cleaning. If you notice a temperature
rise, switch off the vacuum cleaner immediately. Disconnect
the vacuum cleaner from the power outlet and remove the
filter. Remove the vacuumed material from the ash filter.
CAUTION: In case of excessive temperatures, the tubes,
the ash filter, or the vacuum cleaner may be damaged.
Completely empty the vacuum cleaner and the ash
filter in a safe area after the vacuum cleaning. Let both
appliances (vacuum cleaner and ash filter) cool down under
supervision.
POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a
double polarized plug (one with the blade wider than the
other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
WARNING: Be sure to read, understand, and apply
information, entitled 'Safety Instructions & Warnings'.
Do not vacuum in areas with flammable gases, vapors,
or explosive dusts in the air. Flammable gases or vapors
include but are not limited to; lighter fluid, solvent type
cleaners, oil-base paints, gasoline, alcohol or aerosol
sprays. Explosive dusts include but are not limited to; coal,
magnesium, grain or gun powder. To reduce the risk of
health hazards from vapors or dust, do not vacuum toxic
materials.
5
Operating Instructions and Owner's Manual
Publicidad
