cecotec ENERGYSILENCE PURETECH 6500 Manual De Instrucciones página 21

ENGLISH
MODE
- If you press this button once, the 'NORMAL' mode will be active.
- If you press it again, the Eco ('NATURE' on the control panel) mode will be active.
- If you press it once again, the Night mode ('SLEEP' on the control panel) will be active.
TIMER
- When you press this button once, the evaporative cooler will stop working after 1 hour.
- When you press this button again, the evaporative cooler will stop working after 2 hour.
- When you press this button once again, the evaporative cooler will stop working after 3
hour.
- When you press this button for the fourth time, the evaporative cooler will stop working
after 4 hour.
- When you press this button for the fifth time, the evaporative cooler will stop working after
5 hour.
- When you press this button for the sixth time, the evaporative cooler will stop working
after 6 hour.
- When you press this button for the seventh time, the evaporative cooler will stop working
after 7 hour.
- When you press this button for the eighth time, the evaporative cooler will stop working
after 12 hour.
COOL
If you press this button once, the 'COOL' function will be active.
SWING
If you press this button once, the 'SWING' function will be active, so the blades start oscillating.
ION
If you press this button once, the ionising function will be active.
Heating function
- Lower the tab 'Cooling and Heating' located on the side part of the product to the 'Heating'
position. In the heating function, the evaporative cooler will work at a 'medium' steady
speed, since the speed cannot be set.
ON/OFF
- Press the button once to activate the Heat I function on the control panel. The temperature
level will be low.
- Press this button again to turn off the evaporative cooler, if the heat mode is on it will take
up 30 seconds to turn off.
E N E R GYSI L EN CE PURETECH 6500
40
MODE
- Press the button once to activate the Heat II function on the control panel. The heat level
will be high.
- If you press the button again, the evaporative cooler will stop heating.
- If you press the button for the third time, the Heat I function will be active on the control
panel and the heating level will be low.
4. CLEANING AND MAINTENANCE
- Use a soft, damp cloth to clean the device surface. Do not use abrasive or corrosive
products.
- Do not immerse any part of the evaporative cooler in water or other liquids.
- After cleaning, carefully dry the appliance and make sure that all the electrical parts are
completely dry.
- Make sure the air inlet and outlet are clean and protected from dust and dirt.
- If the product is not going to be used for a long period, unplug it and store it in a dry and
safe place.
- You should clean the device once every week.
Fig. 4
Air filter cleaning
- Unplug the product and pull the air filter bracket with your hands to remove it. Clean the air
filter with a neutral detergent and a soft brush. Next, clean it with water.
- Clean the wet filter.
- Remove the wet filter. Clean it with a soft brush, water and a detergent. Next, place it again
in the device along with the air filter.
Warning
- Make sure that the evaporative cooler is disconnected from the power supply before
removing the filter protection.
- Unplug the device during filling and cleaning.
- To avoid leaks, you must install the wet filter correctly.
Water tank cleaning
- Turn off and disconnect the device from the mains supply before cleaning the tank.
- Remove the water tank and clean it with a cloth and detergent. Rinse with water and place
it again on the evaporative cooler.
- Use fresh water to clean and dry it completely.
- Use a dampen cloth to clean the dirt and dust on the surface of the device. Do not use
abrasive or corrosive detergents to clean the product.
ENGLISH
EN E RGYSILEN CE PURETECH 6500
41