Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
1.
Press the ON/OFF button on the control panel or remote control to turn the appliance
on or off. The cooler will start at low speed and with a normal air setting. To return
to Standby mode, simply press the ON/OFF button on the control panel or remote
control.
2.
Speed: there are three air-speed modes (low – medium – high) selectable by pressing
the Speed button. Each time the Speed button is pressed, an icon appears on the LED
display indicating the current speed level.
Mode: press the Mode button to select the type of air. Each time this button is
3.
pressed, an indicator lights up on the display to indicate the type of air. There are 3
air types: Normal–Natural–Sleep.
4.
Timer: press the Timer button to set the operating time of the cooler between 0 and
12 hours; the cooler will go into Standby mode after the pre-set time has elapsed.
Each time the button is pressed, the hours will increase one by one and the time
indicator will light up on the display.
5.
To reset the timer, simply press the button until the time indicator shows "00".
Oscillation: press the Swing button to change the wind direction. The oscillation icon
6.
will appear on the display when the function is activated. Press the button again
to stop oscillation. The vertical direction of air flow can be adjusted manually by
directing the outlet grilles up and down.
Cool: to activate the air-cooling function, press the Cool button. The water pump will
7.
take water from the tank and pour it into the cooling pad. The cooling pad absorbs
heat from the water and the evaporated air is expelled with the help of a fan. The
cool breeze from the cooler lowers the temperature and generates a relaxing
cooling effect.
WARNING:
if the water level is low or the tank is empty, do not activate the Cool function.
Check the water level and add more if necessary. Replace old water with fresh water. It is
recommended to replace the water in the tank at least once a week.
Ioniser
Press the Ion button to activate the ionising function. The ion icon on the display will light up
and negative ions will be released. Ions attract small particles in the air, such as dust, pollen,
mould spores, etc., making them too heavy to hover. This ensures cleaner and purer air in the
environment.
Remote control
The remote control requires a button battery CR2025. Before use, remove the button-battery
protector from the battery slot.
Water tank
Check the water level in the tank regularly. Make sure that the water does not exceed the MAX.
40
ENERGYSILENCE 5500 PURE TECH
mark on the water tank. Activating the Cool function with little water in the tank may cause the
water pump to malfunction and void the product warranty.
Before refilling the water tank, turn off the appliance by pressing the switch on the rear panel
and unplug the power cord.
Filling up the water tank
-
Remove the water tank, located at the bottom rear of the evaporative cooler, and fill it up
one third of its capacity. Please note the water-level indicator when filling the tank.
-
The water level in the tank must not exceed the "MAX" mark.
-
The water level in the tank must be above the "MIN" mark.
-
The ice bricks are placed in the water tank for cold air.
4. CLEANING AND MAINTENANCE
-
After prolonged operation, dust accumulated on the dust filter or cooling pad may
affect the air inlet. It is therefore recommended to clean the cooler regularly. Follow the
instructions below to clean the device.
-
Switch off the appliance and unplug it before cleaning and maintenance.
-
Use a soft, damp cloth to clean the surface of the device. Do not use abrasive or corrosive
products.
-
Do not immerse any part of the air cooler in water or other liquids.
-
After cleaning, carefully dry the appliance and make sure that all the electrical parts are
completely dry.
-
Make sure the air inlet and outlet are clean and protected from dust and dirt.
-
If the product is not going to be used for a long period, unplug it and store it in a dry and
safe place.
-
Clean the appliance at least once a week.
Dust filter
To remove the dust filter, remove the screw first, then simply press the latches with both hands
and pull out the filter. Use a neutral cleaning agent and a brush to clean dust and dirt from the
filter. To reinstall the cleaned filter, place the lower part of the filter first and then push the
upper part until it clicks into place.
Cooling pad
The cooling pad can be seen by removing the dust filter. Press the lock in the centre and gently
pull the pad out. Use a clean, soft brush to remove dust and dirt from the pad. Rinse with water
if necessary and allow it to air dry. Never use any chemical cleaning solution that may damage
the pad.
ENGLISH
ENERGYSILENCE 5500 PURE TECH
41
Publicidad
