Publicidad
Idiomas disponibles
Idiomas disponibles
accessories. You may unexpectedly cause the tool to start possibly causing personal injury.
5. Be aware of the switch location when placing the tool down or when picking the tool up. You may
accidentally activate the switch.
6. After changing the bits or making any adjustments, make sure the collet nut and any other adjustments are
securely tightened. Loose or unsecured adjustment devices can unexpectedly shift, causing loss of control,
and loose rotating components will be violently thrown.
7. Do not reach in the area of the spinning bit. The nearness of the spinning bit to your hand may not always be
apparent or obvious.
8. Brushes should be run at operating speed for at least one minute before using. No one is to be in front or
in line with the brush during this time. This run-in time allows loose wires and bristles to be discharged prior
to work application.
9. Wire and bristle brushes must never be operated at speeds greater than 15,000 rpm and the discharge of
the spinning wire brush must be directed away from the user. Small particles and tiny wire fragments may
be discharged at high velocity during cleaning use with these bristles and become imbedded in your skin.
Bristles or wires will be thrown from the brush at high speeds.
10. Wear protective gloves and face shield when using wire or bristle brushes. Lightly apply wire or bristle
brushes to the work; only the tips of the wires and bristles do the work.
Heavy pressure on bristles overstresses the wire or bristles and will cause them to be discharged.
11. When using grinding wheels or similar attachments, handle the tool and wheels carefully to avoid chipping
and cracking. If the tool is dropped during use, install a new grinding wheel. Do not use damaged wheels
or wheels that may possibly be damaged. Damaged wheels may burst during operation causing fragments
to fly away high speed possibly striking you or bystanders causing personal injury.
12. Handle sharp bits with care and never use dull or damaged bits. Damaged bits may snap during use. Dull
bits require applying more force to move the tool, possibly causing the bit to break.
13. Always use clamps or similar devices to secure the work-piece at all times. Never hold the work-piece in one
hand and the tool in the other to perform work. Allow sufficient space between your hand and the spinning
bit to prevent injury due to "kickback". Round work pieces such as dowel rod, pipe, and tubing tend to roll
while being cut often causing the bit to bite into or jump toward you possibly causing personal injury.
14. Always inspect the work-piece before cutting. Cutting irregularly shaped work pieces may pinch the bit,
causing the user to loose their grasp on the tool.
15. Never start the tool when the bit is engaged in the work-piece. The bit cutting edge may grab the material
causing loss of control of the cutter.
16. Always use the proper direction of feed when carving, routing or cutting. Feeding the tool in the wrong
direction may cause the bit to climb out of the work-piece and/or unexpectedly pull the tool in the direction of
the feed causing possible loss of tool control.
17. If the bit becomes jammed or bogs down in the work-piece, turn the tool "OFF" with the switch. Wait for all
moving parts to stop, and then unplug the tool and work to free the jammed material. If the switch is left in
the "ON" position, the tool could restart unexpectedly causing serious personal injury.
18. Do not leave the tool running unattended! Only when the tool comes to a complete stop is it safe to put
down.
19. Do not grind or sand near flammable materials. Sparks from the wheel could these materials to ignite.
20. Do not touch the bit or collet after use, they are too hot to be touched and will cause burns to bare flesh.
21. Do not alter or misuse the tool. Any alteration or modification is a misuse and may result in serious personal
injury.
22. This product is NOT intended for use as a dental drill in human or veterinary medical applications. Serious
personal injury may result.
23. When using steel saws, cutoff wheels, high speed cutters or tungsten carbide cutters, always have the work
English
Publicidad
