Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
99132
To program a new transmitter, it is necessary to program the transmitter's 8 digit code into the vehicle.
A label with an eight-digit number located on the outside of the Dorman remote. (Original remotes will
have this code on the circuit board).
1.
Sit in the driver's seat; close all doors and the rear gate or trunk
2.
Open and close the driver's door one time.
Within 45 seconds
3.
Open and close the driver's door once. Do not remove the key.
4.
Turn the ignition key from LOCK to ON 10 times within 15 seconds.
5.
A chime will sound once, a buzzer will continue to sound and the interior light will continue to
flash until the transmitter codes are completely registered.
***If you do not perform the steps above within 45 seconds an error will occur and neither a chime nor
the buzzer will sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds
6.
Open and close the driver's door once within 15 seconds and an electronic tone will sound for
30 seconds. If you do not perform the operations within 15 seconds an error will occur and the
electronic tone will not sound. In this event, perform the registration steps again beginning with # 3
above.
7.
Before the chime stops on the door, press the power door lock button to LOCK the same
number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8
times if the leftmost digit of the code is 8.
8.
When you have finished entering the number, push to UNLOCK side within five seconds
9.
Repeat steps 7 through 8 for all digits of the transmitter code going from left to right.
10.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then
repeat steps 7 through 9 a second time with the same transmitter code.
11.
When you have entered the eighth digit the second time an electronic tone will sound for 30
seconds or locks will cycle, after the tone or cycle ends start the vehicle then turn off vehicle, remove
key, open and close door and test remote.
12.
Repeat process to progam additional remotes.
1
Publicidad
Resumen de contenidos para Dorman 99132
- Página 1 To program a new transmitter, it is necessary to program the transmitter’s 8 digit code into the vehicle. A label with an eight-digit number located on the outside of the Dorman remote. (Original remotes will have this code on the circuit board).
- Página 2 (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Dorman Products Inc. could void the user’s authority to operate the equipment.
- Página 3 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device.
- Página 4 Hay una etiqueta con el número de ocho dígitos en la parte exterior del control remoto de Dorman. (Los controles originales tendrán este número en la tarjeta del circuito). Siéntese en el asiento del conductor del vehículo; cierre todas las puertas, el baúl y el capó.
- Página 5 (1) Este dispositivo no debe causar interferencias perjudiciales y (2) este dispositivo debe aceptar cualquier interferencia que pueda recibir, incluyendo aquella que impida su funcionamiento. Los cambios o modificaciones no aprobadas expresamente por Dorman Products Inc. pueden hacer que el usuario pierda el derecho de utilizar el equipo.
- Página 6 Su operación está sujeta a las siguientes dos condiciones: (1) Este dispositivo no debe causar interferencias y (2) este dispositivo debe aceptar cualquier interferencia, incluyendo aquella que impida su funcionamiento correcto.
- Página 7 Une étiquette avec un numéro à 8 chiffres situé à l'extérieur de la télécommande Dorman. (Les télécommandes originales auront ce code sur la carte de circuits intégrés) S'asseoir dans le siège du conducteur; fermer toutes les portières et le coffre ou la portière arrière...
- Página 8 Lorsque vous avez saisi le huitième chiffre une deuxième fois, une tonalité électronique sonnera pendant 30 secondes ou le verrouillage effectuera un cycle. Une fois la tonalité ou le cycle terminé, démarrer le véhicule puis l'éteindre, retirer la clé, ouvrir et fermer la portière et tester la télécommande. Répétez l'opération pour les autres télécommandes programme.
- Página 9 Dorman Products Inc. pourrait annuler l'autorité de l'utilisateur à faire fonctionner l'équipement. MISE EN GARDE IC Le terme IC avant le numéro de certification/enregistrement signifie seulement que les spécifications techniques d'Industrie Canada ont été rencontrées. Le fonctionnement est sujet aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence, et (2) cet appareil doit pouvoir accepter toute interférence reçue, incluant l’interférence...