Publicidad
m
IMPORTANT REMARKS
•
Please read the instruction carefully before installation
•
Follow all instructions, since incorrect installation can lead to severe
injury
•
The installation must be done by a technician following the safety
norms in force
•
Only apply to authorized personnel to replace the feeding cable of the
motor
•
Do not pierce nor insert screws in the whole length of the motor
•
Avoid any contact of the motor with liquids
•
Avoid to crush or knock over the motor
•
Possible tampering or wrong connections are not covered by
guarantee
•
If a manual release is provided, the actuating member is to be installed
at a height less than 1,8m
•
Before installing the drive, remove any unnecessary cords and disable
any equipment not needed for powered operation.
Fig. 4
INSTALLATION
Fix the stirrup G to the wall.
•
•
Insert the crown A in the driving wheel B of the limit switch
(fig.1).
Insert the pulley C on the pivot of the motor D (fig.1).
•
•
Insert the copper pin F on the pulley C.
•
Insert completely the motor in the roll-tube (fig.2).
•
Fix the roll-tube to the driving wheel with m 4 x10 screw
(fig.2).
ELECTRIC CONNECTIONS
•
Operators must be installed with a bipolar switch with a
minimum contact clearance opening distance of at least 3mm
(fig.3).
•
Do not connect more than one motor for every push-button
of command.
•
Reverse the brown and black cables, in order to change the
direction of revolution (fig.3)
•
For installation for awnings, a horizontal distance of at least 0,4 m
is to be maintained between the fully unrolled driven part and any
permanent object
•
The power supply cable should not be exposed to sunlight or rain
directly
•
Assure that all accessories have been fixed so that the motor works
without any mechanical problem. The loading weight should be
matched with the output power of the motor
•
Electrical connection must be done by professional technicians to
operate in conformity with the rules
•
Do not allow children to play with fixed controls
•
Keeps remote controls away from children
•
Frequently examine the installation for imbalance and sings of wear or
damage to cables and springs
•
Do not use if repair or adjustment is necessary
•
Moving parts of the drive must be installed higher than 2.5 m above
the floor or other level that could provide access to it
•
The actuating member of a biased-off switch is to be located within
direct sight of the driven part but away from moving parts. It is to be
installed at a minimum height of 1.5 m
•
Fixed controls have to be installed visibly
•
The appliance can not be used in outside
SERVICIO TÉCNICO TELEFÓNICO (ESP):
¡ 93 566 64 82
serviciotecnico@dimoel.es - www.dimoel.es
LIMIT SWITCH ADJUSTMENT
•
The limit switches system is electromechanical and through a
micro-switch it interrupts the feeding of the motor when the
roller shutter or the awning reaches the limit of opening and
closing.
•
To adjust the opening and closing limit is necessary to turn the
adjusting screw placed on the head of the motor through the
plastic screwdriver included in the box (fig.4).
•
Release the shutter straps from the axis. Feed the motor and
observe the sense of the axis rotation.
Closing limit: rotate the axis in the closing direction until it
•
stops. Re-hook the straps of the blind to the axis.
•
Opening limit: Find the screw on the motor head that
corresponds to the opening limit switch according to the
direction of rotation of the axis indicated by an arrow on the
motor head.
•
Turn the adjusting screw towards (+) to increase the speed of
the motor, turn the adjusting screw towards (-) to decrease it
(fig.4).
•
In case that the motor is powered and it doesn't move in any
direction (or one of the two directions), then is possible the
limit switches are already activated In that case, use the plastic
screwdriver to turn the corresponding adjustment screws on
the head of the motor, turning them towards the + (clockwise)
several times to give it more race (to move the limits it is
necessary to give it a lot of turns).
- 7 -
SERVIÇO TÉCNICO TELEFÔNICO (PT):
¡ 917 467 170
assistencia.dimoel@gmail.com- www.dimoel.es
Publicidad
