Stopping the appliance
1. Set the starter device switch on (OFF/0).
2. Depress the gun trigger and discharge the residual
pressure inside the hoses.
3. Engage the gun safety catch (9).
Restarting
1. Release the safety catch (9).
2. Depress the gun trigger and discharge the residual
air inside the hoses.
3. Set the starter device on (ON/I).
Storage
1. Switch the appliance off (OFF/0).
2. Remove the plug from the socket.
3. Turn o the water supply tap.
4. Discharge the residual pressure from the gun until
all the water has come out of the nozzle.
5. Drain and wash out the detergent tank at the end of
the working session. To wash out the tank, use clean
water instead of the detergent.
6. Engage the gun safety catch (9).
Relling and using detergent
When using detergent, the adjustable nozzle must be set
on "
" (on models with this feature).
Use of a high pressure hose longer than the one originally
supplied with the cleaner, or the use of an additional hose
extension, may reduce or completely halt the intake of
detergent. Fill the tank with highly degradable detergent.
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water
to the surface while still dry. When dealing with vertical
surfaces work from the bottom upwards. Leave the
detergent to act for 1-2 minutes but do not allow the
surface to dry. Starting from the bottom, use the high
pressure jet at a minimum distance of 30cm. Do not allow
the rinse water to run onto unwashed surfaces.
In some cases, scrubbing with brushes is needed to
remove dirt. High pressure is not always the best solution
for good washing results, since it may damage some
surfaces. The finest adjustable nozzle jet setting or the
rotopower nozzle should not be used on delicate or
painted parts, or on pressurised components (e.g tyres,
inflation valves, etc.). Effective washing depends on both
the pressure and volume of the water used, to the same degree.
MAINTENANCE (Fig. E)
Any maintenance operations not covered by this chapter should
be carried out by an Authorized sales and service Centre.
Caution! Always disconnect the plug from the power
socket before carrying out any work on the appliance.
Cleaning the nozzle
1. Disconnect the lance from the nozzle.
2. Remove any dirt deposits from the nozzle hole using
the tool (7).
Cleaning the filter
Inspect the intake filter (13) and detergent filter (if fitted)
before each use, and clean in accordance with the
instructions if necessary.
Unjamming the motor
In case of lengthy stoppages, limescale sediments may
cause the motor to seize. To unjam the motor, turn the
drive shaft with a tool.
End-of-season storage
Treat the appliance with non-corrosive, non-toxic antifreeze
and lubricate the o-rings using the lubricating grease tube
(where sup- plied) as shown before storing it away for winter.
Put the appliance in a dry place, protected from frost.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned and
authorized service locations. All BLACK+DECKER Service
Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. For more
information about our authorized service centers and if you
need technical advice, repair, or genuine factory replacement
parts, contact the BLACK+DECKER location nearest you, or
visit us at www.BlackandDecker-la.com
ENGLISH • 23
(On models with this feature)