Publicidad
Idiomas disponibles
Idiomas disponibles
90565611 PCL120CR Lithium Recip Saw.qxd:??????-00 Cir Saw book
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This is a
normal condition, and does not indicate a problem. To facilitate the cooling of the
battery pack after use, avoid placing the charger or battery pack in a warm environment
such as in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights.
c. Move charger and battery pack to a location where the surrounding air
temperature is approximately 65°F - 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING:
Shock hazard. Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL
WARNING:
Make certain the lock-off button is engaged to prevent switch actuation
before removing or installing battery.
TO INSTALL BATTERY PACK: Insert battery pack into tool,
until an audible click is heard as shown in figure C.
TO REMOVE BATTERY PACK: Depress the battery release
buttons as shown in figure D and pull battery pack out of
tool.
OPERATING INSTRUCTIONS
WARNING: Always wear proper eye and respiratory protection while operating this
tool.
• Use clamps or another practical way to secure and support the workpiece to
a stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to loss of control.
• Place shoe firmly against work to be cut.
• Switch on saw motor and allow it to obtain maximum speed before applying pressure.
C
D
11
8
6/9/10
2:48 PM
Page 8
THREE POSITION SAW (FIGURES E & F)
The tool can be converted into three
different positions. To change positions:
• Slide the pivot release slider (3) to the
right as shown in figure E and rotate the
handle portion of the tool into any of the
three positions shown in figure F.
THREE POSITION SAW WARNINGS:
• To avoid being pinched, keep hands away
from the hinge when changing positions.
• To avoid tool being turned on accidentally,
make sure the lock-off button is engaged.
TRIGGER SWITCH (FIGURE G)
The tool is equipped with a switch lock-off
feature to prevent unintentional operation.
• To switch the tool on, press the lock off
button (2), then squeeze the on/off switch
(1).
• Releasing the trigger turns the motor OFF.
NOTE: This tool has no provision to lock
the switch in the ON position, and should
never be locked in the ON position by any
other means.
ADJUSTING SHOE (FIGURE H & I)
CAUTION: Make sure the lock-off button is engaged to prevent switch actuation
before making any adjustments or removing or installing attachments or accessories.
• Remove the allen wrench (9) from the holder.
E
3
F
G
2
1
9
Publicidad
