Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
This is a high pressure device. To reduce the risk of injury,
user must read and understand operator's manual. To
reduce the risk of injection do not point sprayer at any
part of the body, persons, or unit itself. In case of skin
injection, seek medical attention immediately. Failure to
heed this may cause serious personal injury.
AIRLESS SPRAYING
See Figure 12.
Ensure surface to be painted is free of dust, dirt, and
grease.
Mask or cover any areas not intended to be painted or
stained. Be aware of wind that may cause your paint or
stain to spray into areas not desired. Always use drop
cloths or other cover to protect areas that are not intended
to be painted or stained.
Select spray tip and seat securely into nozzle tip guard.
Arrow on spray tip should face direction of spray.
Lock the sprayer trigger.
Plug in the paint sprayer.
Prime unit. Follow Set Up and Priming instructions.
Turn HI/OFF/FINISH switch to HI.
Turn prime/spray lever to SPRAY.
Turn variable pressure control to HIGH pressure (+). Pres-
sure can be adjusted to reach desired spray pattern and
coverage.
Unlock the sprayer trigger. Begin spraying.
NOTE: If spray tip becomes clogged, lock the sprayer
trigger, turn 180°, unlock sprayer trigger and spray into
waste container to clear clog. Return spray tip to spray
position and continue spraying.
Lock the sprayer trigger and follow Release Pressure
Procedure when finished or stopping for any reason.
PAINTING TIPS
See Figures 13 - 14.
Practice spraying on a piece of scrap material to test your
spray pattern before beginning. If you cannot get a good
spray pattern, see Troubleshooting section.
To create an even coating over the entire surface:
• Keep the pistol-grip sprayer an even distance from the
area being sprayed, about 12 inches from the nozzle
tip guard to the surface being sprayed.
• Operate the pistol-grip sprayer in straight horizontal
strokes. Do not hold the sprayer at an angle. This will
result in uneven coverage.
• Depress the trigger to start the spray at the beginning
of the stroke and release the trigger as you end the
stroke. To prevent material build-up, do not keep the
trigger depressed as you proceed to the next stroke.
OPERATION
• Make one pass for each stroke. Overlap strokes in
halves for full coverage.
When finished, return any unused paint or stain to its
original container and thoroughly clean the sprayer.
WARNING:
To reduce the risk of fire or explosion: Do not use with
flammable liquids (i.e., paint stripper, paint remover,
brush cleaner, mineral spirits, lacquer thinner, turpentine,
acetone, gasoline, kerosene, etc.). Use only water (for
water-based paints) or Klean Strip® Green Safer Paint
Thinner (for oil-based paints or varnish).
FINE FINISH SPRAYING
See Figure 15.
In finish spray mode, pressurized air is introduced into the
paint stream, resulting in a finer finish.
To use finish spray mode:
Remove the cover from the air connect outlet on the
control panel.
Attach the 25-ft. air hose to the air connect outlet. See
Connecting High Pressure Hose/DUAL-ACTION
Pistol-Grip Sprayer.
Attach the other end of the air hose to the DUAL-ACTION
pistol-grip sprayer. See Connecting High Pressure
Hose/DUAL-ACTION
Plug in the paint sprayer.
Prime unit. Follow Set Up and Priming instructions earlier
in this manual.
Turn HI/OFF/FINISH switch to FINISH.
Turn PRIME/SPRAY lever to SPRAY.
Turn variable pressure control to the FINISH setting (-).
Pressure can be adjusted to reach desired spray pattern
and coverage.
Unlock the sprayer trigger. Begin spraying.
NOTE: If spray tip becomes clogged, lock the sprayer
trigger, turn 180°, unlock sprayer trigger, and spray into
waste container to clear clog. Return spray tip to spray
position and continue spraying.
Lock DUAL-ACTION
lease Pressure Procedure when finished or stopping for
any reason.
OVERNIGHT STORAGE (UP TO 12 HOURS)
NOTE: These instructions are for latex paint and water-based
materials only. If you are using oil-based material, refer to
Cleaning the Paint Sprayer and Long Term Storage for
instructions. Stains and oil-based materials do not keep for
any extended period of time.
Lock DUAL-ACTION
Release Pressure Procedure.
Turn HI/OFF/FINISH switch OFF.
12 — English
Pistol-Grip Sprayer.
™
the sprayer trigger and follow Re-
™
pistol-grip sprayer and follow
™
™
™
Publicidad
