Important; Tool Use And Care; Specific Safety Rules For - Urrea RB914A Manual De Usuario Y Garantía

IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
Do not use tools if switch does not turn it on
or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
E N G L I S H •
SERVICE
Tool service must be performed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.

SPECIFIC SAFETY RULES FOR

LI-ION HAMMER DRILLS
ADDITIONAL SAFETY RULES FOR HAMMER
DRILLS
• Do not put pressure on the drill to the ex-
tent that it slows down the motor. For better
results, and to lengthen the life of the drill, al-
low the drill bit to cut without pressure.
• Only use accessories that are in optimal con-
dition.
• Hold the tool by its insulated gripping sur-
faces when performing any operation where
the tool may contact hidden wiring or its own
cord. Contact with a "live" wire will make ex-
posed metal parts of the tool "live", and shock
the operator.
• Check that there is sufficient clearance for the
drill bit under the workpiece before drilling.
• When starting the cordless hammer drill, let
the drill run for a few seconds before using it
on a workpiece. Watch for vibration or wob-
bling that could indicate poor installation of
an accessory.
• Don't get distracted while operating, stop
the cordless hammer drill before turning your
attention to other tasks.
• If possible, always use clamps or a vise to hold
the work.
• Ensure that the lighting is adequate to see
the operation.
• Keep the work area free of tripping hazards.
• Secure the material that is being drilled. Nev-
er hold it in your hand or across your hand or
across your legs.
• Do not use damaged or bowed drill bits.
• Keep hands away from rotating parts.
• Always wear safety goggles and a dust mask
when drilling, especially when drilling above
the level of your head.
• Watch out for flying sparks. Hold the tool so
that any sparks will fly away from the operator
and other persons. Keep all flammable materi-
als away when using this drill.
U se r's m a n ua l
13