Publicidad
Idiomas disponibles
Idiomas disponibles
Chuck removal—Always wear eye protection!
1.
Open chuck jaws to maximum capacity.
2.
Remove retaining screw on tool by turning it in a clockwise direction (screw has a left-hand thread).
3.
Insert the shorter end of a 1/4" or greater hex key into chuck and tighten.
4.
Place tool on its side and hold firmly.
5.
Using a wooden mallet strike the longer end in the clockwise direction.
Chuck installation—Always wear eye protection!
1.
Screw the chuck on by hand as far as it will go.
2.
Insert screw (left-hand thread), and tighten screw securely.
3.
Tighten the chuck around the shorter end of a 1/4" or larger hex key, then strike the longer end in the clockwise direction with
a wooden mallet while holding down the tool securely.
4.
Tighten the screw once again by turning in a counterclockwise direction.
Starting, stopping and controlling speed
1.
To start the tool, depress the lever.
2.
To stop the tool release the lever
3.
To vary the driving speed, simply increase or decrease
pressure on the lever. The further the lever is pulled,
the greater the speed.
Using the forward/reverse switch
The forward/reverse switch is located on the top, back of the
tool as shown.
1.
For forward (clockwise) rotation, push the forward/
reverse switch up.
2.
For reverse (counterclockwise) rotation, push the for-
ward/reverse switch down.
Note: To prevent damage to the motor, allow the tool to come
to a complete stop before reversing.
Stalling (When using tool as a drill)
If tool seems as if it is about to stall, maintain a firm grip and reduce pressure slightly to allow the bit to regain the speed. If the tool does
stall, release the lever switch immediately. Reverse the motor, remove the bit from the work and start again. Do not press the lever switch
on and off in an attempt to start a stalled drill. This can damage the drill.
To use the tool as a drill, while holding the tool pointed away from you rotate the sleeve clockwise. To use the tool as a drill-
driver, while holding the tool pointed away from you rotate the sleeve counter clockwise.
When selecting a bit, use the right type for your job.
Driving Screws
1.
Select the proper style and size 1/4" hex screwdriver bit for the type of screw being used.
2.
Insert the screwdriver bit into the screwdriver.
3.
Insert the screwdriver bit firmly in the head of the screw.
4.
Place the tip of the screw in the pilot hole on the workpiece and squeeze the lever and apply steady and even pressure. At this
point the clutch will engage, driving the screw. Once the screw bottoms out, a ratcheting sound will be heard.
Removing Screws
1.
Reverse the direction of rotation on tool.
2.
Place the bit tip into the screw, squeeze the lever and apply pressure to engage the clutches.When selecting a bit, use the right
type for your job.
Drilling
1.
Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use high-speed
steel twist drill bits or hole saws. For MASONRY, use high carbide –tipped bits. For PLASTICS use low speeds for material
with a low melting point.
2.
When using twist drill bits, pull the bit out of the hole frequently to clear chips from the bit flutes.
3.
Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a back-up block to prevent damage
to the material.
4.
Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit biting, but do not push hard enough
to stall the motor or deflect the bit.
5.
Hold tool firmly to control the twisting action of the drill.
6.
IF THE DRILL STALLS, it is usually because it is being overloaded. RELEASE THE LEVER IMMEDIATELY, remove drill bit
from work, and determine cause of stalling. DO NOT CLICK LEVER OFF AND ON IN AN ATTEMPT TO START A STALLED
DRILL THIS CAN DAMAGE THE DRILL.
FORWARD
REVERSE
3
FORWARD
REVERSE
Publicidad
