Mafell ERIKA 70 Manual De Montaje página 13

The sliding table is used if the stroke length of the pull-
push saw is not sufficient. After installation of the
sliding table (chapter 3.1), the underfloor pull function
can be used again as soon as the sliding table is
fastened (chapter 3.5).
3.1 Assembly sliding table
Danger
Only carry out adjustments on the
sliding table when the saw blade is
stationary and the mains plug has
been unplugged.
The sliding table 1 (Fig. 1) is installed on the left hand
side of the machine as follows:
•
Install the two clamping brackets 2 (Fig. 2) with
the cylinder-head screws 4 (Fig. 3) and washers
5 on the guide tube 3 (Fig. 2). Be sure to use the
outer pair of holes (see Fig. 2).
Note: Inner pair of holes is only for Erika 65.
•
Lightly tighten the cylinder-head screws 4 (Fig.
3).
•
Install the guide tube 3 (Fig. 2) with the clamping
brackets 2 on the left hand dovetail guide of the
table top by pushing the clamping brackets 2 into
the dovetail guide (Fig. 3) from the side.
•
Tighten the cylinder-head screws 6 (Fig. 3) on the
clamping devices.
•
Hook the support table 7 (Fig. 4) into the guide
tube 3 (Fig. 2).
3.2 Adjustment sliding table
•
For adjustment purposes, place the fence guide
extension 8 (Fig. 5) of stop plate 9 onto the
support table 7 (Fig. 4) with the fence guide
extension projecting beyond the machine bench.
•
Release the cylinder-head screws 4 (Fig. 3) on
the guide tube 3 and the cylinder-head screws 6
on the clamping bracket 2.
Explanatory video can
be found at:
www.mafell.de/erika
•
Using the adjusting screw 10 (Fig. 3), adjust the
support table at the two clamping brackets 2 so
that it stands parallel to the machine.
•
Tighten the adjusting screw 10 with the hexagon
nut of the screw.
•
Using the adjusting screws 11 (Fig. 3), adjust the
support table to max. 1 mm above the machine
bench. Adjust the adjusting screws at both
clamping brackets 2.
•
Tighten the adjusting screw 11 with the hexagon
nut of the screw.
•
Tighten the cylinder-head screws 4 and the
cylinder-head screws 6.
3.3 Disassembly sliding table
•
Unhook the support table 7 (Fig. 4) from the
guide tube 3 (Fig. 2).
•
Loosen the cylinder-head screws 6 (Fig. 3) on the
clamping bracket 2 (Fig. 2).
•
Lift the guide tube 3 (Fig. 2) and push the
clamping brackets 2 out of the dovetail guide.
•
If the sliding table is later attached again at the
same position, no adjustment will be necessary.
3.4 Handling sliding table
After installation and adjustment of the sliding table,
you can install the universal guide fence and the multi-
purpose guide fence on the support table.
•
Bring the saw unit in central position (circular saw
bench function).
•
Attach your workpieces at the above-mentioned
fence guides.
•
Switch on the machine and push the workpiece
with the sliding table towards the saw blade.
Note: The sliding table is maintenance-free. Do not
grease or oil the guide tube 3 (Fig. 2).
3.5 Use underfloor pull function
To use the underfloor pull function, fasten the sliding
table as follows:
•
Clamp the support table 7 (Fig. 4) with the wing
bolt 12 (Fig. 6).
-13-