Publicidad
Idiomas disponibles
Idiomas disponibles
Height
Scarifying
For transportation and
+10mm
storage.
Scarifying sensitive lawn.
Dethatching thin layers.
+mm
The second scarifying
operation in autumn.
Scarifying normal lawn.
Dethatching normal
0mm
layer.
Scarifying normal lawn.
-5mm
Dethatching thick layer.
Scarifying rough thick
-10mm
lawn.
Dethatching thick layer.
Changing the height
Push in the height adjustment lever (9) towards wheel
axis side, and move it upwards or downwards.
Overload protection
This machine is equipped with overload protection, and it
functions under the following situations:
The cutting tool becomes clogged because scarified
•
materials are built up around it.
The machine is trying to scarify more than the motor
•
can handle.
Something hinders the rotation of the cutting tool.
•
When this protection works, the machine is switched off
automatically.
If it happens, unplug the machine, wait until it cools down,
and remove the cause of the overload before restarting
the machine.
OPERATION
Operation Tips:
Cut your grass before operation and fertilize after the
•
operation.
Adjust the depth of the cutting tool in accordance with
•
the height of the grass and weather.
Avoid operating on wet grass. It tends to stick on the
•
discharge port and other parts of the machine. It may
also cause slip and fall.
Do not move too fast. Push the machine slowly.
•
Otherwise discharge port may become clogged and the
motor may overloaded.
•
Operate along a line as straight as possible.
Make slightly overlapping scarified lines. It will maintain
•
even and smooth surface.
When a flower bed is included in the operating area,
•
make a circle or two around the flower bed.
Be especially careful when turning the machine.
•
Do not stay in one position. It damages the grass.
•
Tips for scarifying:
Always take the weather into account. Warm, sunny
•
and wet weather is good for scarifying because the
lawn can recover healthily. On the other hand, avoid
cold, heat, dry weather.
https://tm.by
Интернет-магазин TM.by
Usage
Raking
(Optional accessory)
For transportation and
storage.
Raking sensitive lawn.
Dethatching thin layers.
Raking normal lawn.
Raking rough thick lawn.
Do NOT use for raking
operation.
Do NOT use for raking
operation.
During spring season scarify the lawn.
•
If summer is wet, scarify the lawn in early autumn.
•
Refrain from scarifying during period of extremely hot
•
weather.
If summer is very dry, do not scarify in autumn.
•
Tips for raking:
Plenty amount of air is needed for the area around the
•
roots of the lawn in order to maintain healthy growth in
spring season.
It is recommended performing aeration operation on the
•
lawn every 4 – 6 weeks in accordance with the state of
the lawn.
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off
•
and unplugged before performing inspection or
maintenance.
Wear protective gloves before performing inspection or
•
maintenance.
The cutter does not stop immediately after switch off.
•
Wait until all the parts stop before performing any
maintenance work.
Make sure that all the tools are removed after
•
maintenance work.
Never use gasoline, benzine, thinner, alcohol or the like
•
for cleaning. Discoloration, deformation or cracks may
result. To clean the machine, use only moist cloth and
soft brush.
Do not hose or clean the machine with high pressured
•
water.
When transporting the machine, pay attention to the
following points:
Switch off the motor, unplug and wait until the cutting
•
tool stops.
Adjust the depth of the cutting tool to transportation
•
height.
Always transport the machine by its handle.
•
Avoid heavy impact or strong vibration.
•
Secure the machine firmly in case it is embarked on
•
vehicles.
Perform the following steps after each operation:
Switch off the motor, unplug and wait until the cutting
•
tool stops.
Clean the grass catcher. Store it in a dry room.
•
Check, clean and store the machine in a dry room.
•
Perform the following work at regular basis:
Check all the clamps, such as screws, nuts etc. are
•
tightly fasten.
Check for defects such as loose, worn, or damaged
•
parts. Replace them if necessary.
Check that the covers and guards are not damaged or
•
deformed.
If the machine starts vibrating abnormally during
•
operation, that may be caused by unbalanced or
deformed cutting tool due to the impacts by foreign
objects. Have the cutting tool repaired or replaced by
authorized service center if it happens.
The cutting tool is worn out during the course of time.
•
Check the condition of the cutting tool and its stability on
regular basis. Replace it if it is worn or become blunt.
Clean and lubricate all screw parts before storage.
•
Publicidad
