Descargar Imprimir esta página

WERKU WK500490 Instrucciones Originales página 2

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 7
ENG
CE DECLARATION CONFORMITY.
Werku
®
declares that the WK500490 airless
gun is in accordance with the European
Directives and Standards 2006/42/CE and
EN12621:2006+A1:2010.
La Coruña, 01/02/2018.
R Yáñez
Werku Tools SA
TECHNICAL CHARACTERISTICS.
Airless pump >0.5 HP (375 W)
60-160 bar
Maximum pressure 250 bar
thread NPS 1/4"
Outlet thread BSP 7/8"
temperature 5-40ºC
Net weight 0.380 kg
<89 dB(A)
Acoustic pressure LwA <90.82 dB(A)
Vibration Ah <0.715 m/s².
SAFETY INSTRUCTIONS.
Read all security warnings and all instructions
Failure to follow all warnings and instructions
listed below may result in electrical shock, fire
and/or serious injury
all instructions for future reference
can be avoided in many cases by recognizing a
potentially hazardous situation before it occurs and
by observing appropriate safety procedures
not use this airless gun for other applications than
those specified in this manual.
SAFETY PRECAUTIONS.
Be safety-conscious
regulations governing ventilation, fire prevention,
and operation must be observed
Injection injury
A high pressure stream produced
by this airless gun can pierce the skin and
underlying tissues, leading to serious injury and
possible amputation
injury as a simple cut
amputation
See a physician immediately
Inform the physician of the type of coating
material or cleaning agent with which the injury
was caused
The maximum operating range of
this airless gun is 250 Bar fluid pressure
Working pressure
Material temperature <43ºC
Acoustic pressure LpA
Keep all warnings and
Accidents
All local and national
Hazard:
Do not treat an injection
Injection can lead to
aim the airless gun at any part of the body
allow any part of the body to touch the fluid stream
Do not allow body to touch a leak in the fluid
hose
Gloves will not provide protection against an
injection injury
anyone else
shut the pump off and release all pressure before
servicing, cleaning the tip or guard, changing
tip, or leaving unattended
released by turning off the motor
spray valve must be turned to prime to relieve the
pressure
described in the pump manual
tip guard in place while spraying
Inlet
provides some protection but is mainly a warning
Working
device
flushing or cleaning the system
develop leaks from wear, kinking and abuse
leak can inject material into the skin
the hose before each use
gun without a trigger lock and trigger guard in
place and in good working order
must be rated at or above the maximum
operating pressure range of the airless gun
This includes spray tips, extensions and hose
Hazard: Explosion hazard due to incompatible
materials will cause severe injury or property
damage
bleach or chlorine
Do
hydrocarbon solvents such as bleach, mildewcide,
methylene chloride trichloroethane
not compatible with aluminum
coating material supplier about the compatibility
of material with aluminum
This airless gun can cause severe injury or
property damage
safety precautions before operating this airless
gun
Never spray near sources of ignition; eg
open flames, cigarettes (also cigars and pipes
are sources of ignition), sparks, hot wires and
hot surfaces, etc
when spraying
with a protective mask
related illness, the manufacturer's regulations
for the materials, solvents, and cleaning agents
used must be observed when preparing, working
Never
with and cleaning the airless gun
2
English
Never put hand in front of the airless gun
Never point the airless gun at
Always lock the airless gun trigger,
Pressure will not be
Refer to the pressure relief pressure
Always remove the spray tip before
Never use an airless
Do not use materials containing
Do not use halogenated
Hazard: General
Read all instructions and
Wear respiratory equipment
The operator must be provided
In order to prevent work
Never
The prime/
Always keep the
The tip guard
The hose can
A
Inspect
All accessories
They are
Contact your
Protective

Publicidad

loading