Publicidad
Idiomas disponibles
Idiomas disponibles
ATX / ATX2-xxx-X/PH5-xx
ATX / ATX2-xxx-X/BF5-xx
ATX / ATX2-xxx-X/Le2-xx
Wiegand / Clock & Data
1
2 3 4 5 6
0 Vdc
+Vcc
Code / D0
Data / D1
Clock
Terminal block Connector
Use an AC/DC power supply type LPS, Limited Power Source (as per IEC/UL/EN 60950-1 Ed2) or type ES1, PS1 (according to IEC/UL/EN 62368-
1) for the main supply.
Main power supply:
Communication:
RS485 (L+ & L-) / RS232 (TD & RD) / TTL (Wiegand / Clock & Data)
Protection:
IP65, excluding connectors
The operating mode for the Buzzer and LED 1 and 2 can be programmed by a configuration card (SCB / OCB) or controlled by the remote
system with a 0 Vdc respectively on the "Led 1", "Led 2" and "Buzzer" inputs of the reader's connector or controlled by the c ommunication
protocol of the reader (SSCP® / OSDP
Tearing is detected by an accelerometer. When the reader is wrenched, the switch output (connector J2) provides an O/C contact to indicate
the tearing of reader.
for R/S 31/x1: the wrenching signal will be emitted on the "Data/Data1" line. This function is configurable via a configurati on card.
▪
for R/S 32/33/x2/x3 and OSDP
▪
for W 32/33/x2/x3: the reader will perform the operations configured with the SSCP
▪
Caution: switch on the reader when it is in its final position to initialize the accelerometer in the correct position.
LEGIC readers are configurable by serial link for non-secure parameters and by master card SAM to access secure data on user's card.
Reader retrieve configuration from SAM at any time.
If the SAM is accepted, LED lights green, maintain the SAM in front of the reader until the buzzer beeps 5 times.
-
If the SAM is not accepted, LED lights red and buzzer is activated 1s.
-
Mifare® R and S readers are configurable with SCB RFID configuration card.
OSDP
readers are configurable with OCB RFID configuration card or with FileTransfer command.
TM
If the SCB/OCB is compatible with the reader's firmware, the LED lights green and the buzzer beeps five times.
▪
If the SCB/OCB is not compatible with the reader's firmware, the LED lights red and the buzzer is activated for 1 s.
▪
If the SCB/OCB key is different from the reader's key: no reaction.
▪
Caution: set your reader with your own company key.
ATEX & IECEX reader
Installation procedure
ATX / ATX2 13.56MHz MIFARE
X= E: 13.56MHz Mifare®
X= I / IM: 13.56MHz Mifare®+ 125kHz
X= E: 13.56MHz Legic®
7 8 9 10
0 Vdc
Buzzer
+Vcc
Led 2
Led 1
Type x31
(Wiegand)
1
2
3
Data 0 (D0)
4
Data 1 (D1)
5
Clock
6
NC
NC
7
8
9
10
Range +7 Vdc up to +28 Vdc
).
TM
: the reader will perform the operations configured with the configuration card.
TM
© STid - 20 PA des Pradeaux FR13850 Gréasque – NI1104X05 - Page 4 sur 15 - Ed. 25/05/2023
Lecteur ATEX & IECEX
Notice d'installation
/ 13.56MHz MIFARE
&125kHz / 13.56MHz LEGIC
®
®
RS232
1
2 3 4 5 6
7 8 9 10
Buzzer
Led 2
Led 1
Tx
Rx
Type x31
(Clock & Data)
0 Vdc
+Vcc (+7 Vdc / +28 Vdc)
Code
Data
Clock
NC
NC
Led 1
Led 2
Buzzer
Power Supply Characteristics
Typical: +12 Vdc
Characteristics
Buzzer / LED
Anti-Tearing
Read-only reader configuration
ATEX & IECEX lectores
Manual de instalación
RS485
1
2 3 4 5 6
0 Vdc
+Vcc
L+
L-
Type x32
Type x33
(RS232)
(RS485)
NC
NC
NC
NC
NC
NC
Tx
L +
L -
Rx
protocol.
®
US
FR
ES
7 8 9 10
Buzzer
Led 2
Led 1
Publicidad
