Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
- The pump does not require maintenance as
long as the following precautions are taken:
when there is a risk of freezing, empty the pump
by removing the suction tube, ensuring that the
pump is primed when it is started again, check
that the foot valve is cleaned at regular inter-
vals, if the pump is to remain inactive for an
extended period of time it is advisable empty it
completely, rinse it with clean water and store it
in a dry place. if the arrow does not turn freely,
release it using a screwdriver, there is a hole in
the back of the pump that gives access to the
arrow, turn it with the help of the screwdriver,
if this does not solve the problem remove the
pump body, by loosening the corresponding
mounting screws and clean it perfectly to re-
move any incrustation.
NEVER CARRY OUT WORK ON THE PUMP
WITHOUT FIRST DISCONNECTING IT FROM
THE MAINS.- TO IDENTIFY WHERE THE WATER
LEAKS ARE, DRY THE MOTOR PUMP AND PIPING
AND FILL IT UP AGAIN WITH WATER.
- Below you will find a box with the problems
that may arise.
- If you find any failure in your motor pump,
even out of the Guarantee term or if you need-
ed to repair the product by yourself, we remind
you that we have authorized service shops.
CONSIDERATIONS TO INSTALL THE WATER TANK
It is recommended to install a foot valve with
a diameter wider than the pump´s suction to
avoid losses due to friction.
DISPOSING OF THE APPLIANCE
This product must not be disposed of in house-
hold rubbish. You must dispose of such old elec-
trical and electronic equipment separately.
- Please check with your local authority about
the possibilities for correct disposal.
Through separate disposal you send old equip-
ment for recycling or for other forms of re-use.
You will thus help to avoid in some cases that
damaging material gets into the environment.
DISPOSING OF THE PACKAGING
The packaging consists of cardboard and corre-
spondingly marked plastics that can be recycled.
- Make these materials available for recycling.
14
TROUBLESHOOTING
DANGER: Improperly conducted repairs may
prevent your appliance from working safely.
Such re airs will endanger you and your sur-
roundings.
Minor faults are often sufficient to cause a
malfunction. In most cases, you will be able to
correct these faults easily yourself. Please start
by referring to the following list before contact-
ing our technical support. This will help you save
much effort and possibly expense.
PROBLEMS THAT MAY ARISE
Possible failure. Corrective action
THE PUPM SPILLS WATER
Loose or badly sealed pipes. Identify the place of
the leak and use some type of sealant (SURTEK
threads sealer tape, Cement, Pola, etc.) When
doing the connections again.
Damaged coupling seal and/or loose screws.
Replace the damaged parts and securely tighten
the screws, being careful not to strip them.
Defective mechanical seal. Replace the dam-
aged parts and assembly again your motor
pump making sure no part is loose.
MOTOR WOULD NOT START
False contact in the installation or in the motor
connection. Verify that all the connections are
well done. If not, do them again and protect
them correctly.
Loose, broken or incorrect wires. Verify the
wiring, if correct, connect it again, tighten the
connections and replace defective wires.
Burnt fuses or thermomagnetic switch tripped.
Replace the fuses or close the switch. Make sure
that the size of the fuses is correct according to
the current consumption of the motor. Verify
there is no short circuit in the motor line.
Defective start-up device. Replace it if damaged
or if not appropriate for the size of the motor.
Motor shaft or other elements rotate stuck.
Verify there are no objects preventing the free
motion of the rotor, shaft or impeller.
Check that the bearings are in good condition.
Motor coil burnt. Visit an authorized service
workshop.
THE MOTOR TURNS ON AND OFF CONTINU-
OUSLY
Low voltage in the line. Verify that the wire
used is appropriate. Install a voltage regulator
or check it with the electrical supply company.
®
Publicidad
