Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTALLATION AND SET UP FOR HOMEAWARE™
The HomeAware™ HA360DB Doorbell Transmitter will alert you when someone comes to visit. The
HomeAware™ doorbell transmitter requires no wires and can be installed in seconds. You can add up to
four additional transmitters to accommodate other doors or use the doorbell transmitter as a portable
personal SOS alerter.
The HomeAware™ doorbell transmitter will alert you to someone at the door via the HomeAware™ Main
unit. The Main unit receives a wireless signal from the doorbell transmitter and will flash the built in
strobe, make a loud sound and/or vibrate a bed shaker, or any pre selected combination of the three.
Once the Main unit receives the signal from the doorbell transmitter it will then send a signal to all
HomeAware™ remote receivers. In addition to the HomeAware™ receivers, if using our optional bridge
unit you will also be alerted to the doorbell transmitter through your traditional Sonic Alert remote
receivers (SA102, SA201, BL300, and SB1000).
Install Batteries
The HomeAware™ doorbell transmitter comes with two #357 silver oxide long lasting batteries that need
to be installed into the bottom of the unit. Once installed the red light should light when the button is
pushed. If the light does not show, you may have the batteries in backwards.
Linking Doorbell Transmitter to Main Unit
This procedure will link your doorbell transmitter to your HomeAware™ Main unit. The Main unit will also
provide an alert to all HomeAware™ remote receivers. When using the Sonic Alert Bridge unit all original
Sonic Alert receivers (SA101, SA201, BL300, and SB1000) will also alert you. It is best to do the LINK
procedure in the same room as close as possible to the HomeAware™ Main unit.
To link the doorbell to your HomeAware™ Main unit follow the steps below.
1. Press Set Up button on the Main unit and the word LINK will be shown on the display, press Enter.
LINK will begin blinking.
2. Press the link button on the bottom of your doorbell unit and a red blinking dot will start blinking on top
of the doorbell. DONE will scroll across screen when linked.
HA360DB – Doorbell Transmitter
1
Publicidad
Resumen de contenidos para HomeAware HA360DB
- Página 1 The HomeAware™ HA360DB Doorbell Transmitter will alert you when someone comes to visit. The HomeAware™ doorbell transmitter requires no wires and can be installed in seconds. You can add up to four additional transmitters to accommodate other doors or use the doorbell transmitter as a portable personal SOS alerter.
- Página 2 Note: There are two methods to install/set up the doorbell transmitter, both require batteries Stand-alone no chime box. With this method no existing doorbell chime box is available. Placement of the transmitter must be within 50ft of the HomeAware™ Main unit (See Step 1 for doorbell transmitter set up below).
- Página 3 Step 2) Installation to Existing Powered Door Chime With this method you can install the HomeAware™ transmitter to your existing AC powered doorbell chime. This method allows you to use the existing doorbell button so there aren’t two buttons outside.
- Página 4 INSTALLATION AND SET UP FOR HOMEAWARE™ HA360DB – Doorbell Transmitter Continued FCC Requirements This device complies with part 15 of the FCC rules, and with RSS-210 of Industry Canada. Operation is subject to the following two conditions; (1) This device might not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Página 5 The HomeAware™ HA360DB is warranted against manufacturing defects in materials and workmanship for one (1) year from the date of purchase. Within this period Sonic Alert will repair or replace at our option the HomeAware™ HA360DB without charge for parts and labor.
- Página 7 SOS. El transmisor de timbre HomeAware™ le alertará si hay alguien en la puerta a través de la unidad principal del HomeAware™ La unidad principal recibe una señal inalámbrica desde el transmisor de la puerta y parpadeará...
- Página 8 Continuación Enlazando el Transmisor del Timbre a la unidad principal Este procedimiento enlazará su transmisor del timbre a su unidad HomeAware™ Principal. La unidad principal también proporcionará una alerta a todos los receptores remotos HomeAware™. Cuando se utiliza la unidad Puente Sonic Bridge Alert todos los receptores originales de Sonic Alert (SA101, SA201, BL300 y SB1000) también le alertarán.
- Página 9 CONFIGURACIÕN DEL TIMBRE TRANSMISOR Continuación Paso 1) Instalación sin caja carillón de timbre existente Continuación b) Desmonte la tapa del tornillo en la parte superior de la unidad de timbre, la tapa posee el logotipo de Sonic Alert sobre ella, la misma se deslizará para desmontar. Una vez desmontada, verá el agujero de montura del tornillo superior.
- Página 10 Paso 2) Instalación cuando existe un carillón conectado Con este método se puede instalar el transmisor HomeAware™ a la toma de AC del carillón del timbre de puerta existente. Este método le permite utilizar el botón del timbre existente, de modo que no habrá...
- Página 11 CUMPLIMIENTO NORMATIVO PARTE 68 DE LA INFORMACIÓN DE LAS REGLAS FCC El equipo HA360M cumple con la Parte 68 de las Reglas FCC. Usted debe, previa solicitud, facilitar el número de registro FCC y el REN a su compañía telefónica local. Ambos números se muestran en la etiqueta de su equipo HA360M.
- Página 12 GARANTÍA LIMITADA POR 1 AÑO DE SONIC ALERT El HomeAware™ HA360M está garantizado contra defectos de fabricación en materiales y mano de obra por un (1) año a partir de la fecha de compra. Dentro de este período, Sonic Alert reparará o reemplazará, a su criterio, el HA360M sin cargo por componentes o trabajo.