Publicidad
Idiomas disponibles
Idiomas disponibles
• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt battery
system.
• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not
have a battery installed.
• Excessive engine cranking can damage a vehicle' s starter motor. If the engine fails to start after the recommended number of
attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.
• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and
recharging. To avoid possible damage that may shorten the unit' s working life, protect it from direct sunlight, direct heat and/or
moisture.
FIRST AID
SKIN: If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes. If redness, pain, or
irritation occurs, seek immediate medical attention.
EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate
medical attention.
saVe tHese iNstruCtiONs
iNtrODuCtiON
Congratulations on purchasing your new 450A Jump-Starter with Compressor. Read this Instruction Manual and follow the
instructions carefully before using this unit.
CHargiNg/reCHargiNg
Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self-
discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost through
self-discharge. When the unit is not in frequent use, manufacturer recommends the battery be recharged at least every 30 days.
Notes:
This unit is delivered in a partially charged state – you must fully charge it upon purchase and before using it for the first time. Initial AC charge should be
for 40 hours.
Recharging battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life. The
battery can be recharged using the Built-In 120 Volt AC Charger.
Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
Charging/recharging using the 120 Volt aC Charger and a standard Household extension Cord (not included)
1. Lift the AC adapter cover located on the top of the unit and connect an extension cord to the unit. Plug the other end of the
cord into a standard 120-volt AC wall outlet.
2. Charge until the green Battery Status LED Indicator lights solid or flashes.
3. Disconnect the extension cord and depress the battery status button. If all 3 status lights illuminate, the unit is fully charged.
JuMP-starter
This Jump-Starter is equipped with an On/Off Power Switch which is located at the right hand side of the Front Panel under a
protective cover. Once the connections are properly made, turn the switch on to jump-start the vehicle.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place vehicle in "park" and
set the emergency brake.
2. Make sure the Jump-Starter Power Switch is turned to off.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis)
(MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery' s positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body part. Never clamp
directly to negative battery terminal or moving part. Refer to the automobile owner' s manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Note:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a and
4b above with steps 5a and 5b, then proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery' s negative terminal.
5b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. Never
clamp directly to Positive battery terminal or moving part. Refer to the automobile owner' s manual.
6. When clamps are connected properly, lift up the protective cover and turn the Jump-Starter Power Switch to ON.
7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
8. Turn the Jump-Starter Power Switch back to the OFF position.
9. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
J45TK_ManualENSP_053012.indd 6-7
6
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE "SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS"
SECTION OF THIS INSTRUCTION MANUAL.
• This power system is to be used ONLY on vehicles with 12-volt DC battery systems.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or explosion.
• After use, turn the Jump-Starter Power Switch off.
• Replace worn or defective parts immediately.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting this
type of vehicle, read the vehicle manual to confirm that external-starting assistance is advised.
• Excessive engine cranking can damage the vehicle's starter motor. If the engine fails to start after the recommended number of
attempts, discontinue jump-start procedure and look for other problems that need to be corrected.
• If the connections to the battery' s positive and negative terminals are incorrect, the Reverse Polarity Indicator will light and the
unit will sound a continuous alarm until the clamps are disconnected. Disconnect clamps and reconnect to battery with correct
polarity.
• If vehicle fails to start, turn off the ignition, turn off the Jump-Starter Power Switch, disconnect the jump-start system' s leads and
contact a qualified technician to investigate why the engine did not start.
• Recharge this unit fully after each use.
12 VOLt DC POrtaBLe POwer suPPLy
The 12 volt DC power supply is located under a protective cover at the left hand side of front panel. Refer to the illustration in the
features section to locate. This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory
outlet plug and are rated up to 5 amps.
1. Lift up the cover of the unit 's 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED A 5 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically press the battery power level pushbutton to check battery status. (When all three battery status LEDs light, it
indicates a full battery. Only one red battery status indicator light indicates that the unit needs to be recharged.)
usB POwer POrt
The USB power port is under the same protective cover as the 12 volt DC accessory outlet at the left hand side of front panel. Refer
to the illustration of the features section to locate.
1. Push the USB Power Button to turn the USB Port on and the USB power indicator will light.
2. Lift up the cover of the USB Charging Port.
3. Plug the USB-powered device into the USB Charging Port and operate normally.
4. Periodically press the battery power level pushbutton to check battery status. (When all three battery status LEDs light, it
indicates a full battery. Only one red battery status indicator light indicates that the unit needs to be recharged.)
Notes:
This unit' s USB Power Port does not support data communication. It only provides 5 volts/500mA DC power to an external USB-powered device.
Make sure the USB Power Button is in the off position when the unit is being recharged or stored.
Some household USB-powered electronics will not operate with this unit.
2-LeD area LigHt
The built-in 2-LED Area Light is located at the middle of the front panel and is controlled by the Area Light Power Button. Refer to
the illustration in the features section to locate. Press the Area Light Power Button once to turn the lights on. Press the Area Light
Power Button again to turn the lights off. Make sure the 2-LED Area Light is turned off when the unit is being recharged or stored.
Periodically check the unit' s battery status by pressing the Battery Power Level Button. (When all three Battery Status LED
Indicators light, it indicates a full battery. If only one Red Battery Status Indicator lights, it indicates that the unit needs to be
recharged.)
POrtaBLe COMPressOr
The built-in 12 Volt DC Compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. The
compressor hose with tire fitting is stored in the storage compartment. The Compressor Power Switch is located in the top of the
front panel and the air pressure gauge is located at the back of the unit. Refer to the illustration in the features section to locate.
The compressor can operate long enough to fill up to 3 average sized tires before the battery must be recharged.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting an appropriate nozzle to the
air hose. Return hose to the storage compartment after use.
inflating tires or Products with Valve stems
1. Lift the thumb latch on the nozzle (chuck) and fit it onto the valve stem.
2. Ensure nozzle connector is pushed on to valve stem as far as possible before closing thumb latch.
3. Make sure latch is secure.
7
5/30/2012 10:56:39 AM
Publicidad
