Descargar Imprimir esta página

Milwaukee 2606-20 Manual Del Operador página 3

Ocultar thumbs Ver también para 2606-20:

Publicidad

Idiomas disponibles

Idiomas disponibles

ASSEMBLY
WARNING
Recharge only with the
charger specifi ed for the battery. For specifi c
charging instructions, read the operator's
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
OPERATION
WARNING
Always remove battery
pack before changing or removing acces-
sories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
WARNING
To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Installing Bits
Always remove the battery before inserting or
removing bits. Select the proper style and size bit
for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the coun-
terclockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck's operation.
Selecting Drill or Drive Action
(Cat. No. 2606-20)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until
the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different
materials and to prevent damage
to the screw or tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2607-20)
1. To use the hammer-drilling
mode, rotate the application
selector collar until the hammer
symbol
appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
NOTE: The number selected on
the torque selector collar has no effect on opera-
tion of the drill in hammer mode.
NOTE: When using carbide bits, do not use wa-
ter to settle dust. Do not attempt to drill through
steel reinforcing rods. This will damage the
carbide bits.
2. To use the drilling only mode,
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
4
3. To use the driving screws
mode rotate the application
selector collar until the drive
symbol
appears in line with
the arrow. Then rotate the torque
selector collar until the desired
clutch setting appears in line with
the arrow.
The adjustable clutch, when properly adjusted,
will slip at a preset torque to prevent driving the
screw too deep into different materials and to
prevent damage to the screw or tool.
The torque specifi cations shown here are approximate
values obtained with a fully charged battery pack.
Cat. No. 2606-20
Clutch
Applications
Setting in. lbs
1-5
15-30
Small screws in softwood.
6-10
32-40
Medium screws in softwood or small
screws in hardwood.
11-15
43-50
Large screws in softwoods. Medium
16-17
55-100
screws in hardwood or large screws in
hardwood with pilot hole.
Cat. No. 2607-20
Clutch
Applications
Setting in. lbs
1-3
28-30
Small screws in softwood.
4-6
31-33
Medium screws in softwood or small
7-9
34-39
screws in hardwood.
10-13
41-47
Large screws in softwoods. Medium
14-17
49-55
screws in hardwood or large screws in
18
57
hardwood with pilot hole.
NOTE: Because the settings shown in the table are only
a guide, use a piece of scrap material to test the different
clutch settings before driving screws into the workpiece.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to
display "1".
2. For High speed, push the speed selector to
display "2".
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow
the motor to come to a complete stop before using
the control switch.
For forward (clockwise)
rotation, push in the con-
trol switch from the right
Forward
side of the tool. Check
the direction of rotation
Lock
Push to
before use.
CENTER
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while
the control switch is in the center locked position.
Always lock the trigger or remove the battery
pack before performing maintenance, changing
accessories, storing the tool and any time the tool
is not in use.
WARNING
To reduce the risk of injury,
always hold or brace securely.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handles fi rmly and
pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To vary the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
3. To stop the tool, release the trigger. Make sure
the bit comes to a complete stop before laying
the tool down.
Drilling
Place the bit on the work surface and apply fi rm
pressure before starting. Too much pressure will
slow the bit and reduce drilling effi ciency. Too little
pressure will cause the bit to slide over the work
area and dull the point of the bit.
If the tool begins to stall, reduce pressure slightly
to allow the bit to regain speed. If the bit binds,
reverse the motor to free the bit from the workpiece.
5
Reverse

Publicidad

loading

Este manual también es adecuado para:

2607-20