Publicidad
Idiomas disponibles
Idiomas disponibles
How to start the dishwasher
How to start a wash cycle...
After performing all the operations described in the previous chapters,
turn the water tap on completely, press ON-OFF button "A" situated
on the control panel and indicator light "B" comes on.
At this point, the dishwasher is on and ready to be programmed.
Starting and selecting the cycle.
Turn the cycle selector knob "D" clockwise until the reference notch
on the knob corresponds with the number or symbol for the cycle
you wish to set (consult the wash cycle table on page 17, especially
when first using the appliance).
If the appliance door is shut, press the Start button "R" and you will
hear a beep; the cycle will start up within a few seconds.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights "G" which come
on in sequence as the appliance is performing that specific phase of
the wash cycle.
These phases are:
pre-wash,
wash,
Cancelling or modifying a wash cycle in progress.....
Premise: You can cancel the wash cycle in progress, if it has only just
started.
To modify a wash cycle, keep the RESET button "R" pressed for
about 5 seconds: a prolonged beep will sound, followed by three
short beeps. Indicator light "G" will turn off and at this point, all the
settings will have been cancelled.
To select a new wash cycle, repeat the operations illustrated in the
paragraph entitled "starting and selecting the cycle".
Warning: the knob must be turned clockwise from wash cycle 1 to
7, an anti-clockwise from wash cycle 7 to 1.
If you have left out a dish...
You can interrupt a wash cycle by pressing the ON- OFF button,
then place the dishes you had left out into the appliance, which will
start up from where it was interrupted when you turn it back on.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity comes
back on or when the door is shut.
At the end of the wash cycle....
The end of the wash cycle is indicated by two short beeps and the
flashing of the drying phase indicator light.
Warning:
Turn the appliance off by pressing button "A", unplug the
appliance from the electricity socket to cut off the power
supply; the power supply cable should consequently be
easily accessible.
GB
All manuals and user guides at all-guides.com
rinses,
drying
• Turn off the water tap.
• Wait a few minutes before unloading the dishes: if you wait a little
while they dry better thanks to the steam.
• Empty the lower rack first.
Warning:when you open the dishwasher door after the wash cycle
has just ended or is under way, take care not to scald yourself with
the hot steam.
When you have loaded the dishes, you can choose when to start
your dishwasher before setting the wash cycle desired. Press button
"H" to delay the start of the wash cycle by 12, 9, 6 or 3 hours. Each
time you press it, you will hear a short beep and the indicator light
"G" corresponding to the selected delay will light up.
Now you can select the desired wash cycle. Press the start button
"R" and after you hear the beep, the countdown to the delayed
start will begin.
Once this time is up, the indicator light will stop flashing and the
wash cycle will begin.
If you have set a 12 hour delay, for example, once you have selected
the wash cycle, the 12 hour indicator light will flash, followed by
the others in sequence until the set time delay is up. A quick look at
the indicator lights will keep you informed of the countdown progress
at all times.
Have you changed your mind?
If you change your mind, you can set a shorter time delay: press
button "H" to select it. You need not reset the wash cycle.
If on the other hand you want to cancel the delay set and you want
the cycle to start immediately, press button "H" repeatedly until the
cycle starts and indicator light "G" corresponding to the cycle start
phase comes on.
Dual function of indicator lights "G"
1) flashing to indicate a delayed start:to remind you that you
have set a delayed start;
2) on and not flashing beneath the cycle phase symbol:
meaning the cycle has started and is in the phase indicated by the
symbol.
You want to wash on one rack only?
Remember to use half the amount of detergent.
When you only have little cutlery to wash, you can run just half a
load on the upper rack, saving on water, detergent and electricity.
• When you press the "I" button, you will hear a blip and the "L"
indicator light will light up.
Once you have made your selection, start the wash cycle by pressing
Start and it will wash the top rack only.
- This option is available with all wash cycles.
- The Just You wash cycle is programmed to wash on the
upper rack only.
16
Publicidad
