Selecting The Operating Mode; Mode Manual; Mode Scan; Mode Preset - IMG STAGELINE TXS-900 Manual De Instrucciones

Ocultar thumbs Ver también para TXS-900:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29
6 Operation
Connect the power supply unit provided to the
power supply jack (11) and to a mains socket
(230 V/ 50 Hz) . After connection to the power
supply, the receiver is switched on .
To switch the receiver on or off, use the button
POWER (2): Keep the button pressed for approx .
1 second .
If the receiver is not in use for a longer period of
time, disconnect the power supply unit from the
mains socket . Even when the receiver is switched
off, the power supply unit has a low power con-
sumption .
7 Setting the Transmission Channel
To set the transmission channel, the receiver offers
3 operating modes . Use the buttons SET,
(5) to make the settings .
When setting the channel, make sure that any
switched-on transmitters of wireless systems
operated at the same time are not too close to the
receiver (minimum distance: 1 m) .

7.1 Selecting the operating mode

The display indicates the current operating mode:
"MANUAL", "SCAN" or "PRESET" (A) . To select
the desired mode, use the button
the button pressed for approx . 1 second to go to
the next mode (or keep the button pressed until
the mode is indicated, then release it) .

7.2 Mode MANUAL

In the mode MANUAL, the desired radio frequency
can be selected manually from the 442 radio fre-
quencies available (
1) Use the button
or
UAL (
chapter 7 .1) . The display will indicate
the most recent radio frequency (G) and corre-
sponding channel number (E) adjusted in the
mode MANUAL or SCAN .
2) To activate the setting mode, keep the button
SET pressed for approx . 1 second until the chan-
nel indication (E) and the frequency indication
(G) start flashing .
Note: When no button is pressed, the setting mode
will be exited after a few seconds .
3) Use the button
steps of 25 kHz) . To run through the frequencies,
keep the corresponding button pressed .
4) The setting mode will be exited automatically
after a few seconds or when the button SET
is pressed .
or
table ➊, page 13) .
to select the mode MAN-
or
to set the frequency (in

7.3 Mode SCAN

In the mode SCAN, the receiver will automatically
find the next free channel . When multiple systems
are operated at the same time: Before performing
the channel scan, switch on the transmitters that
have already been set to a transmission channel .
Thus, all channels already being used or incompat-
ible with the channels already set will be skipped
during the channel scan . In this mode, depending
on local conditions, up to 12 channels can be oper-
ated at the same time without mutual interference .
1) Use the button
(
chapter 7 .1) . The display will indicate the
most recent radio frequency (G) and correspond-
ing channel number (E) adjusted in the mode
MANUAL or SCAN .
2) To activate the setting mode, keep the button
and
SET pressed for approx . 1 second until the chan-
nel indication (E) and the frequency indication
(G) start flashing .
Note: When no button is pressed, the setting mode
will be exited after a few seconds .
3) To start the channel scan, press the button
(scan in ascending order) or
ing order) . The scan will stop when the next
interference-free channel is reached . As long as
the setting mode is still activated, the scan will
: Keep
always restart when the button is pressed again .
4) The setting mode will be exited automatically
after a few seconds or when the button SET
is pressed .

7.4 Mode PRESET

In the mode PRESET, a channel can be selected from
one of 4 preset groups ("P1" . . . "P4") (
page 13) . Each group includes 8 intermodula-
tion-free channels, i . e . channels which may be
used at the same time without mutual interference .
Thus, this mode is suitable for operating multiple
systems at the same time . In case of interference
occurring at the place of operation, select a dif-
ferent group or use the mode SCAN to set the
channels for the systems .
1) Use the button
PRESET (
cate the most recent radio frequency (G) and
corresponding channel number (E) adjusted in
this mode . The indication GP (B) will display the
group to which the frequency has been assigned
("P1" ... "P4"); the indication CH (C) will display
the channel number of the frequency within this
group ("1" ... "8") .
or
to select the mode SCAN
or
to select the mode
chapter 7 .1) . The display will indi-
(scan in descend-
☞ 
table ➋,
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

25.5230

Tabla de contenido