Publicidad
Idiomas disponibles
Idiomas disponibles
• Tighten the first screw.
• If the clutch ratchets before the desired
result is achieved, increase the collar
setting and continue tightening the
screw. Repeat until you reach the correct
setting. Use this setting for the remaining
screws.
Dual Range Gearing
The dual range feature of your drill allows
you to shift gears for greater versatility.
• To select low speed, high torque setting
(position 1), turn tool off and permit to
stop. Slide dual range gear selector (5)
away from the chuck.
• To select the high speed, low torque
setting (position 2), turn tool off and
permit to stop. Slide gear shifter button
back toward the chuck.
NOTE: Do not change gears when tool is
running. If you are having trouble changing
gears, make sure that the dual range gear
button is either completely pushed forward
or completely pushed back.
Keyless Chuck
WARNING
:
Make certain the battery
pack is removed to prevent tool actuation
before installing or removing accessories.
To insert a drill bit or other accessory:
1. Grasp the chuck (6) and rotate it in
the counterclockwise direction, as
viewed from the chuck end.
2. Insert the bit or other accessory fully
into the chuck, and tighten securely
by rotating the chuck in the clockwise
direction as viewed from the chuck end.
WARNING
:
Do not attempt to tighten
or loosen drill bits (or any other accessory)
by gripping the front part of the chuck and
turning the tool on. Damage to the chuck
and personal injury may occur when
changing accessories.
Drilling
WARNING
:
Drill may stall if
overloaded causing a sudden twist.
Always expect the stall. Grip the drill firmly
to control the twisting action and avoid
injury.
(Shift drill into DRILL mode)
• Use sharp drill bits only.
• Support and secure work properly, as
instructed in the Safety Instructions.
• Use appropriate and required safety
equipment, as instructed in the Safety
Instructions.
• Secure and maintain work area, as
instructed in the Safety Instructions.
• Run the drill very slowly, using light
pressure, until the hole is started enough
to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the
All manuals and user guides at all-guides.com
• Hold the drill firmly with two hands,
• DO NOT CLICK THE TRIGGER OF A
• Minimize stalling on breakthrough by
• Keep the motor running while pulling
• Make sure switch turns drill on and off.
Drilling in Wood
Holes in wood can be made with the
same twist drill bits used for metal or with
spade bits. These bits should be sharp
and should be pulled out frequently when
drilling to clear chips from the flutes.
Drilling in Metal
Use a cutting lubricant when drilling
metals. The exceptions are cast iron
and brass which should be drilled dry.
The cutting lubricants that work best are
sulfurized cutting oil or lard oil.
Screw Driving
secure before starting the tool. A loose bit
may eject from tool causing possible
personal injury.
(Shift drill into SCREW mode)
• For driving fasteners, the forward/reverse
• Use reverse (button pushed to the right)
NOTE: When moving from forward to
reverse, or vice versa, always release the
trigger switch first.
Battery Fuel Gauge - Figure E
The tool is equipped with a battery fuel
gauge (9).
This can be used to display the current
level of charge in the battery during
use and during charging. It does not
indicate tool functionality and is subject to
variation based on product components,
temperature and end-user application.
Checking battery charge during use:
• Press and hold the battery fuel gauge
• The three LEDs (E2) will illuminate
• If LED light does not lluminate, charge
9
bit. Use enough pressure to keep the
bit biting but not so much as to stall the
motor or deflect the bit.
one hand on the handle, and the other
gripping the bottom around the battery
area or the auxiliary handle if provided.
STALLED DRILL OFF AND ON IN AN
ATTEMPT TO START IT. DAMAGE TO
THE DRILL CAN RESULT.
reducing pressure and slowly drilling
through the last part of the hole.
the bit out of a drilled hole. This will help
reduce jamming.
WARNING
:
Always ensure the bit is
button should be pushed to the left.
for removing fasteners.
button (E1).
indicating the percent of charge in the
battery (Figure E).
battery.
Publicidad
