IMG STAGELINE WSA-24R Manual De Instrucciones página 7

STATUS PAIR
6 7 8
4) For initial operation, the receiver and the
transmitter must be paired. For this pur-
pose, place the transmitter close to the
receiver first.
5) Connect the transmitter to a mains socket
via its power supply unit. As long as the
transmitter and the receiver have not
been paired, the LED STATUS (7) will flash.
Put the antenna (6) in a vertical position.
6) For pairing:
a) Keep the button PAIR (8) of the trans-
mitter pressed for 3 seconds; the LED
STATUS starts flashing more rapidly
(2 ×/sec.).
b) As long as the LED STATUS flashes rap-
idly (for 10 seconds approx.), keep the
button PAIR (5) of the receiver pressed
for 3 seconds; the button PAIR of the re-
ceiver and the LED STATUS of the trans-
mitter will light permanently. After
successful pairing, a signal will sound at
the output of the receiver.
c) If pairing has failed, wait for 15 seconds
and repeat the process (when the LED
STATUS starts flashing slowly again).
d) Repeat the process for further receivers,
if required.
7) Set up the transmitter at its final position
and supply it with power via its power
supply unit.
8) Feed the audio signal to be transmitted
(e. g. from an MP3/CD player, radio) to the
XLR jacks or 6.3 mm jacks INPUT (12).
4 Operation
1) Once the transmitter and the receiver
have been successfully paired, they will be
paired automatically each time they are
operated again. The button PAIR (5) and
the LED STATUS (7) will light permanently.
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
ST L R
MONO PEAK
AC INPUT:
9 V~ 500 mA 50/60 Hz
9 10 11
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
®
Transmitter
WSA-24T
2) For mono operation, engage the button
ST/MONO (9). For stereo operation, disen-
gage the button.
3) If one of the LEDs PEAK (10) lights up,
there is overload at the input (12): Reduce
the output volume at the signal source ac-
cordingly.
4) After operation, disconnect the power
supply units from the mains sockets. For
convenient operation, connect the power
supply units to a power strip with on/off
switch.
5 Specifications
Audio frequency range: . . . 20 – 20 000 Hz
THD: . . . . . . . . . . . . . . . . . < 0.3 %
Channel separation: . . . . . > 90 dB
Input
Level: . . . . . . . . . . . . . . 1.35 V max.
Connection: . . . . . . . . . XLR, 6.3 mm jack
Output
Level: . . . . . . . . . . . . . . 1 V max.
Connection: . . . . . . . . . 6.3 mm jack
Transmission frequency: . . 2.4 GHz, (25 channels)
Range:. . . . . . . . . . . . . . . . approx. 30 m without
Latency:. . . . . . . . . . . . . . . 18 ms
Power supply: . . . . . . . . . . ~ 9 V via power supply
Dimensions (W × H × D) w/o antenna / weight
WSA-24R:. . . . . . . . . . . 116 × 35 × 86 mm / 118 g
WSA-24T: . . . . . . . . . . . 130 × 54 × 130 mm / 470 g
Subject to technical modification.
INPUT
LEFT RIGHT
12
obstacles
unit provided, connected
to 230 V/ 50 Hz
7