Publicidad
Idiomas disponibles
Idiomas disponibles
English
nOTE: The amount of water drained from the tank after
each use will depend on the time of use and the amount of
humidity in the operating environment. If no water comes
out of the drain valve, the valve may be clogged. If the valve
is clogged, release all air pressure from tank. The valve can
then be removed, cleaned and reinstalled.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by BOSTITCH, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only BOSTITCH
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact BOSTITCH Industrial Tool Co.,
701 East Joppa Road, Towson, MD 21286, call
1–800–433–9258 or visit our website: www.BOSTITCH.com.
Repairs
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a BOSTITCH
factory service center or a BOSTITCH authorized service
center. Always use identical replacement parts.
WARNING: Risk of Unsafe Operation. Unit cycles
automatically when power is on. When servicing,
you may be exposed to voltage sources, compressed
air, or moving parts. Before servicing unit unplug or
disconnect electrical supply to the air compressor,
bleed tank of pressure, and allow the air compressor
to cool.
To Replace Regulator/manifold
(Fig. A, E)
1. Release all air pressure from air tank. See To Drain Tank
in the Maintenance
section.
2. Unplug unit.
3. Remove the panel
11
.
4. Using an adjustable wrench remove the safety valve
from the regulator manifold, pressure gauges
quick connect bodies
6
.
5. Remove the hose by removing the hose clamp
nOTE: The hose clamp is not reusable. You must
8
purchase a new hose clamp, see Replacement Parts in
the service section or purchase a standard hose clamp
at a local hardware store.
Fig. E
12
4
6. Reapply pipe sealant to safety valve, pressure gauges,
and quick connect bodies
7. Reassemble all components in reverse order of removal.
Use wrenches to tighten all components.
Storage
Before you store the air compressor, make sure you do the
following:
1. Review the Maintenance section on the preceding
pages and perform scheduled maintenance as
necessary.
2. Drain water from air tank. See To Drain Tank
under Maintenance.
WARNING: Water will condense in the air tank. If not
drained, water will corrode and weaken the air tank
causing a risk of air tank rupture.
3. Protect the electrical cord and air hose from damage
(such as being stepped on or run over). Wind air hose
loosely around the compressor handle. Wrap electrical
cord onto the cord wrap.
4. Store the air compressor in a clean and dry location.
Service
Replacement Parts
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at www.servicenet.
bostitch.com. You can also order parts from your nearest
BOSTITCH Factory Service Center or BOSTITCH Authorized
Warranty Service Center. Or, you can call our Customer Care
Center at 1–800–556–6696.
Service And Repairs
All quality tools will eventually require servicing and/or
replacement of parts. For information about BOSTITCH,
its factory service centers or authorized warranty service
centers, visit our website at visitar www.BOSTITCH.com
or call our Customer Care Center at 1–800–556–6696. All
8
repairs made by our service centers are fully guaranteed
5
9
, and
against defective material and workmanship. We cannot
guarantee repairs made or attempted by others.
12
.
You can also write to us for information at Bostitch
Fastening Systems, 701 E. Joppa Road, Towson , MD 21286
Publicidad
