Publicidad
Idiomas disponibles
Idiomas disponibles
LENGTH OF CHARGE
20.
a. Test the battery for state of charge. Do not charge if it is over 75% charged or the battery is determined to be defective.
b. Set beginning amps charge rate for size of battery and state of charge per charts.
c. Charge for length of time per charge.
d. Discontinue charge when the specific gravity of electrolyte reaches 1.260 or above. A temperature compensating hydrometer should be used
for this reading. Discontinue charge if the battery begins to gas excessively or if the temperature of the electrolyte reaches approximately
125F. Do not overcharge batteries. Overcharging results in excessive water loss and eventual damage to the battery.
BATTERY SIZE
Am pere Hours
Reserve Capacity
Cold Cranking Am ps
STATE OF CHARGE
Specific Gravity
Open Circuit Voltage 12V
ASSEMBLY INSTRUCTIONS
21.
Attach the handle to the charger using the four screws provided.
CHARGER CONTROL LAYOUT
22.
The control has a large 4-line 20-character LCD display. User interface is thru a 4-button keypad with an ON/OFF,
Arrow Up, Select, and Arrow Down keys. ON/OFF primary use is for turning the charger ON and OFF the other 3
keys are primary used for setting the different parameters available to the end user.
OPERATING INSTRUCTIONS: CHARGING
23.
When the charger is connected to AC Power, the display will show manufacture and program version. It will then
default to the charge-type screen. On this screen the user can select a Partial Charge (will return about 75%),
Complete Charge (this charge is controlled by the entered parameters), Reflash Power, MEMSAVR, Crank, or
Manual. Use the Arrow Up or Arrow Down keys to scroll to the desired type of charge then press the "Select" key. If
a Partial or Complete Charge was selected it will display the Battery Type Selection screen at this point, select the
battery type by using the arrow keys and then pressing "Select". At this point will ask if a "Battery Connected" if it is
press "Select" to start right way or wait 10-second and it will start on its own. You can return to the charge type-screen
by pressing the ON/OFF key.
● Reflash Power: Used to hold the voltage on the battery at the set value while the vehicle is being serviced. Do not use without battery.
● MEMSAVR (MEMORY SAVER): Used to hold up the vehicle voltage while charging the battery. Plug cable into the power plug, then set
charger for Memory Saver and press ON/OFF to start. If it does not see a voltage on the Memory Saver it will show an Error.
● Crank: Used to assist starting a vehicle. Select and follow the screen prompts.
● Manual: This mode can be used to operate the charger just like a manual charger runs for the time set while limiting the current and voltage.
(See section 20. LENGTH OF CHARGE).
CHARGER SETUP
24.
The charger has several parameters that can be set to enhance the charger's operation or the user experience. To enter this set-up menu
PRESS and HOLD the "Select" key (about 5 seconds). The Display will show the menu of items that may be changed:
● LCD Contrast: Use to optimize the contrast on the display for optimum viewing.
● Use Buzzer: Used to turn the buzzer on and off.
● Language: Used to select the language to be used in the display.
● Parameter Lock: Used to lock all the settings for the various battery types.
● Volts at Bat: Voltage Drop; this is used to calibrate cable/clamp voltage drop. This should only need to be done if a large discrepancy
between the display voltage and actual battery voltage exists. To use, select while connected to a battery, unit will turn on in the midrange
current, place a calibrated meter on the battery terminals, then use the arrow keys to adjust the display voltage to match meter on the battery.
When they match, press the "Select" key.
● Jump Conn mOhms: Used to determine voltage drop for line drop calculations.
● Man Test: Used to test the unit in production.
● Amp Output: Used to calibrate the current reading.
● Use SOC: Used to turn the SOC and Est. Time on or off.
● Master Reset: Used to reset all charge parameter to factory default.
BATTERY SIZE TABLE
SM ALL
M EDIUM LARGE
40
60
60
90
275
350
STATE OF CHARGE TABLE
75%
50%
25%
1.225
1.185
1.140
12.4
12.1
11.9
CHARGE RATE Vs. M INUTES CHARGE
BATTERY SIZE % CHARGE
80+
100+
0-25
SM ALL
25-50
400+
50-75
0-25
M EDIUM
25-50
50-75
DEAD
0-25
1.110
LARGE
25-50
11.8
50-75
3
M INUTES
15 30 45 60 75 90
45
30
30
25
25
20
30
20
20
15
15
10
A
M
15
10
10
10
5
5
P
50
45
40
35
30
E
R
45
30
25
20
20
20
E
25
15
15
10 10 10
S
55
55
50
45
45
60
40
35
30
30
30
30
20
20
15 15 15
Publicidad
