Bosch PSM 100 Manual Original página 11

Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Sander
Only use the power tool for dry sanding. Water entering
u
a power tool will increase the risk of electric shock.
Warning: Danger of fire! Avoid overheating the work-
u
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
Technical data
Multi Sander
Article number
Rated power input
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-4.
Bosch Power Tools
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding and polishing of
wood, filler and varnished surfaces. It is particularly well-
suited for profiles, corners and hard-to-reach areas.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Dust box, complete (microfilter system)
(3) Sanding plate
a)
(4) Sanding sheet
(5) Handle (insulated gripping surface)
(6) Extraction outlet
(7) Filter element (microfilter system)
a)
(8) Extraction hose
(9) Dust extraction adapter
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
PSM 80 A
3 603 C54 0..
W
-1
min 13000
-1
min 26000
2
cm 104
mm
kg 0.90
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power
level 94 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
English | 11
a)
PSM 100 A
3 603 CB7 0..
80 100
13000
26000
104
1.4 1.4
0.90
/II
1 609 92A 83K | (05.07.2022)
/II