Publicidad
Idiomas disponibles
Idiomas disponibles
M6.
screw
M5X12.
Bolt M6 X 12
x 4
x 4
Screw M5 X 12
x 2
M6 Flange nut
Philips
x 1
Wrench
x 1
screwdriver
Unscrew the switch button, load small
3/16" screw
to secure
3/16" Screw
x 8
Philips
Screw M5 X 12
x 1
x 4
screwdriver
3/16" Screw
x 4
Philips
x 1
screwdriver
30
PICTURES
1
ASSEMBLY PROCEDURES
1. Assemble the wheel assembly to the
bottom plate. Fix the wheel assembly to the
bottom plate using 4pcs bolt M6X12 and 4pcs
flange nut
M6.
Hardware Used
EE
Bolt M6 X 12
FF
M6 Flange nut
II
Wrench
1
2-1.
Unscrew the switch button, load small
3
battery, tighten the switch button.
2-2. Insert the pins of the base to the holes of
lower support, press to secure the pins. Using
3
4pcs screw M5X12 to secure the lower support
and base.
Insert the pins of the control box assy to the
holes of upper support, press to secure the
pins. Using 4pcs screw
3/16" screw
the upper support and control box assy.
EE
Hardware Used
M
Screw M5 X 12
GG
L
FF
3/16" Screw
DD
GG
Philips
JJ
screwdriver
2
CC
5. Assebmle the flame screen to the upper
4
6
support.
30
Secure the flame screen to the upper support
AA Battery (1.5 V)
7. Carefully install the glass tube by lifting up
using 8pcs screw 3/16".
and inserting through the center hole in the
upper plate. Ensure the black silicone ring is
J
attached to the lower edge of the glass tube
Hardware Used
as illustrated. Slide the glass tube through the
hole of the lower plate cover and onto the
D
K
middle plate. Check and ensure that the glass
DD
3/16" Screw
tube is positioned properly and is completely
covering the center hole of the middle plate.
Philips
DD
DD
JJ
screwdriver
N
WARNING! The black
silicone ring must be in place
prior to operating the heater.
6. Assemble the reflector onto the flame
screen.
Screw the 3pcs stud on the flame screen,
7
8. Assembly the protective guard.
9
put 3pcs washer Φ6 onto the top of stud,
Hang the hooks of the protective guard onto
then put the reflector onto the stud, secure
the holes in supports.
them with 3pcs washer Φ6 and 3pcs wing
31
Secure the protective guards with fixing
nut.
brackets with 4pcs 3/16" screws.
To aid in installation
Hardware Used
place black silicone
Hardware Used
ring on the middle
plate and then
AA
Wing nut
DD
3/16" Screw
install glass tube.
Ensure the rim of
the glass tube sits
BB
Washer Φ6
Philips
JJ
firmly in the black
screwdriver
silicone ring.
CC
Stud
Fixing
HH
Bracket
BLACK SILICONE
RING
8
DD
32
1a
1
x 4
x 4
EE
Front
x 1
M
FF
3. Assemble block belt.
2
4
Fix the block belt to the 2pcs of lower support
behind the front door, using 2pcs
CC
5. Assebmle the flame screen to the upper
support.
Hardware Used
Secure the flame screen to the upper support
AA Battery (1.5 V)
using 8pcs screw 3/16".
GG
Screw M5 X 12
to secure
J
Hardware Used
Philips
JJ
screwdriver
K
DD
3/16" Screw
Philips
DD
JJ
x 4
screwdriver
x 4
N
x 1
4. Assemble the middle support.
Insert the 4pcs upper support to the lower
support. Secure them with 8pcs screw 3/16".
6. Assemble the reflector onto the flame
5
7
screen.
Screw the 3pcs stud on the flame screen,
Hardware Used
7
B
put 3pcs washer Φ6 onto the top of stud,
then put the reflector onto the stud, secure
them with 3pcs washer Φ6 and 3pcs wing
DD
3/16" Screw
nut.
Philips
DD
JJ
x 8
Hardware Used
screwdriver
AA
Wing nut
x 1
BB
Washer Φ6
CC
Stud
6
AA
9. Attach the three side panels to the heater
8
10
using 18pcs screw 3/16".
Note : Do not cover the front side where
32
the control knob is.
Hardware Used
BB
DD
3/16" Screw
E
x 3
x 4
Philips
JJ
screwdriver
x 6
x 1
x 3
x 4
10. Install the knob to M4X6 screw. Hang the
chain to the hole on the control box assy and
put the pothook of front panel to the holes of
bottom plate.
2
Back
3
5
screw
M5X12.
5
B
x 2
x 1
DD
x 8
L
x 1
GG
4
6
8
AA
D
x 8
To aid in installation
DD
x 1
BB
place black silicone
ring on the middle
plate and then
x 3
install glass tube.
Ensure the rim of
the glass tube sits
x 6
firmly in the black
silicone ring.
x 3
BLACK SILICONE
RING
9
11
DD
HH
x 18
DD
x 1
10
31
Publicidad
