Publicidad
Idiomas disponibles
Idiomas disponibles
12 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........
Volts
n
.......
0
A ........
Amperes
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
Hertz
...... Class II
Watts
....
minutes
.....
Alternating
....
Current
.....
Direct
.../min..
Current
No-Load
Speed
ADDITIONAL SAFETY INSTRUCTIONS
f Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal
parts of the power tool "live" and shock the operator.
f Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling,
as it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting a drill bit or screwdriver bit
keyed chuck (Fig. B)
f Open the chuck by turning the sleeve (9)
counterclockwise.
f Insert the bit shaft (8) into the chuck.
f Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. C)
f Open the chuck as far as possible.
f Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f Remove the Allen key.
Construction
f Remove the chuck by turning it counterclockwise.
Earthing
f To refit the chuck, screw it onto the spindle and secure
Terminal
it with the chuck retaining screw.
Safety Alert
Symbol
USE
Revolutions
or Recipro-
Warning! Let the tool work at its own pace. Do not
cation per
minute
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
FOR HAMMER DRILL
Publicidad
