Publicidad
Idiomas disponibles
Idiomas disponibles
1. Fill the water tank with tap water or a mixture of tap
water and no more than 50% distilled water up to the
"MAX" mark.
The device is ready for use.
Switching off the device
1. Turn the power switch to "OFF" position.
Illustration N
The device has been switched off.
2. Press the steam lever until no more steam flows out.
Illustration O
The steam boiler is depressurised.
3. Set the child lock to the rear.
The steam lever is locked.
4. Push the cap on the device socket down and discon-
nect the steam connector from the device socket.
5. Pull the mains plug out of the socket.
6. Drain the water reservoir.
Rinsing out the steam boiler
Rinse the device's steam boiler out after every
eighth filling of the tank.
1. Switch the device off; see Chapter Switching off the
deviceSwitching off the device.
2. Allow the device to cool down.
3. Drain the water reservoir.
4. Remove the accessory/accessories from the acces-
sory holders.
5. Open the cap of the accessory compartment.
6. Remove the accessory/accessories from the acces-
sory compartment.
7. Open the maintenance lock. To do this place the
open end of an extension tube on the maintenance
lock, insert this into the guide so it engages and
open it.
Illustration S
8. Fill the steam boiler with water and swing it around
vigorously. Lime residue which has been deposited
on the bottom of the steam boiler will be released as
a result.
9. Drain the water completely out of the steam boiler.
Illustration T
Storing the device
1. Store the power nozzle and round brush in the ac-
cessory compartment.
2. Connect a manual nozzle to one extension tube.
3. Connect the extension tubes to the accessory hold-
ers.
4. First insert the extension tube and then the spotlight
nozzle in the accessory storage compartment
5. Hang the floor nozzle in the park bracket.
Illustration Q
6. Wind the steam hose around the extension tube and
connect the steam gun to the floor nozzle.
Illustration R
7. Store the mains cable in the storage for the mains
cable.
8. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning it
before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet cleaning.
Freshening up textiles
Prior to using the appliance, always check the compati-
bility of the textiles at a concealed point: Steam down
the textile, allow it to dry and then check it for any
change in colour or shape.
Cleaning coated or painted surfaces
ATTENTION
Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings
or paint and edge band from edges.
Do not direct the steam at glued laminated edges as the
edge band may loosen.
Do not use the appliance for cleaning unsealed wood or
parquet floors.
Do not use the appliance for cleaning painted or plastic
coated surfaces such as kitchen or living room furniture,
doors or parquet.
1. To clean these surfaces, steam a cloth briefly and
use it to wipe over the surfaces.
ATTENTION
Glass breakages and damaged surfaces
Steam can damage sealed points of the window frame
and, at low outside temperatures, lead to tension on the
surface of window panes and hence to glass breakages.
Do not direct the steam at sealed points on the window
frame.
At low outside temperatures, heat up the window panes
by gently steaming the full surface of the glass.
Clean the window area with a manual nozzle and
cover. To remove the water, use a squeegee or wipe
the surfaces dry.
How to use the Accessories
The steam gun can be used for the following applica-
tions without accessories:
For removing slight creases from the hanging cloth-
ing items: Steam the clothing item from a distance of
10-20 cm.
For wiping damp dust: Steam a cloth briefly and use
it to wipe over the furniture.
The spotlight nozzle is suitable for cleaning areas, joins,
fittings, drains, sinks, WCs, blinds or radiators that are
difficult to access. The closer the spotlight nozzle is to
the soiled area, the greater the cleaning efficiency will
be as the temperature and steam volume are at their
highest at the nozzle opening. Larger lime deposits can
be treated before steam cleaning with a suitable deter-
gent. Allow the detergent to soak in for
approx. 5 minutes and then steam it off.
1. Slide the spotlight nozzle onto the steam gun.
Illustration H
English
Glass cleaner
Steam gun
Spotlight nozzle
15
Publicidad
