Publicidad
Idiomas disponibles
Idiomas disponibles
1. N
1.1 g
enerAl nOtes On sAfety
This operation manual is applicable for the hand tool WS
10.
The hand tool may only be handled by personnel
who are qualified.
It is imperative that you observe the safety instruc-
tions provided separately for the drive.
1.2 u
se Of the mAchine fOr purpOses fOr
which it is intended
The hand tool is designed for dry processing on metal
surfaces, for polishing and satin finishing with tool diam-
eters which are max. 150mm.
1.3 i
ncOrrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 d
eclArAtiOn Of incOrpOrAtiOn
The manufacturer Suhner Schweiz AG of Industriestrasse
10, CH-5242 Lupfig, hereby declares for the partly com-
pleted machinery (see reverse side for type and serial no.)
that the following fundamental requirements of the Direc-
tive 2006/42/EC are applied and fulfilled in accordance
with Annex I: 1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.3.7, 1.3.8.1,
1.5.1, 1.5.4, and 1.6.1. Technical documentation was gen-
erated for the partly completed machinery in accordance
with Annex VII of the Machinery Directive. Document
Agent: T. Fischer. Authorised sites are provided with this
technical documentation in paper or electronic form on
justified request. This partly completed machinery may
be put into operation only when the machine in which the
partly completed machinery is to be incorporated has
been ascertained to fulfil the conditions under the Ma-
chinery Directive. CH-Lupfig, 09/2021. T. Fischer/Division
manager
2. C
2.1 A
ssemBly instructiOns
hand tools.
Use only hand tools, shafts, and grinding tools in perfect
condition.
Attach the hand tool to the shaft only when the drive is
switched off and has come to a stop.
Connect grinding tools only when the drive is switched off
and has come to a stop.
16
S
oTES oN
aFETy
ommISSIoNINg
It is imperative that you
read Sections 2 and 3 be-
fore you start operating the
It is imperative that you use the guards intended for the
hand tool.
Observe the specifications applying to your country.
2.1.1 A
/
ttAching
detAching the hAnd tOOl
Press the locking button and insert the hose coupling into
the hand tool hole. Make sure that the locking button is
engaged.
Follow these instructions in reverse order to detach the
hand tool.
2.1.2 A
/
ttAching
detAching the grinding tOOl
Hold the spindle on the wrench flat with an open-end
wrench (1). Attach the press disk (2), with the flat side
facing the grinding tool. Attach the grinding tool (3). At-
tach the second press disk (4), with the flat side facing the
grinding tool. Unscrew the nut with an open-end wrench
(5).
Follow these instructions in reverse order to detach the
grinding tool.
Use only those tools recommended by SUHNER.
You must also observe the safety instructions is-
sued by the manufacturer of the tool.
You must check that the tool's diameter is within the limits
and the max speed is higher than the tool's idle or set
speed.
The tool shaft must fit precisely in the receiver.
The tool must be secured as deeply as possible in the
receiver. The larger the exposed shaft length and the
shorter the clamped length, the lower the max speed.
The installed tool must be able to rotate freely. Afterwards
a test run must be conducted without load for at least thir-
Publicidad
